NT support tool (V053-E1-1) (986753), страница 50
Текст из файла (страница 50)
*1GeneralLabelSettingsCopy FromNumeral TableString TablenCodeEntry (Text Box)*1:Press11to set the label.S Creating the [Step] button and the [Reset] button(11) Create the [Step] button and the [Reset] button in the same manner as the[Man.] button.For the [Step] button and the [Reset] button, change the properties asshown below.[Step] buttonGeneralLabelSettingsCopy From Numeral TableString Table[Reset]buttonn, Stepn, Resetnn1213CodeEntry (Text Box)403Creating the Sample DataSection 9-3S Creating the button group title bar(12) Select [Objects] (menu bar) → [Fixed Display] → [Polyline].(13) While pressing the shift key, drag the polyline from start point to the secondvertex, and then from the second vertex to the third vertex.
Repeat this procedure to create the desired form. Release the Shift key just before reaching at the last point.Reference: To draw continuous polyline, press shift key when drag operation is finished. Dragging this end point creates continuous polyline.(14) Use the properties as they are.S Creating the “Select” (character) string(15) Select [Objects] (menu bar) → [Fixed Display] → [Text].(16) Click the mouse with the mouse cursor set at the position where the “Select”character string is to be displayed (at the intended upper left corner of text).In the (character) string setting (Fixed Display–text) dialog box, set “Select”.(17) Set the properties as shown below.SelectDescriptionPosition––Font TypeStandardScale1SmoothingnAttributeStandardColour1 (Equal)ForegroundWhiteBackgroundBlack(18) Adjust the position of the “Select” (character) string on the data creationscreen by dragging it.(19) Specify the “Select” (character) string, then select [Draw] (menu bar) →[Bring to Front].The “Select” (character) string is brought to the front of the title bar.Creating the [Menu] button, [Monitor] button, and [Alarm] button404Creating the Sample DataSection 9-3S Copying and pasting the buttons from screen No.
11(1) Copy the “Switch Screen” (character) string, frame (rectangle), [Menu] button, [Set] button, and [Alarm] button collectively and paste them to screenNo. 3.(2) Adjust the display position of the pasted (character) string, frame (rectangle), and buttons.S Modifying to the [Monitor] button(3) Double click the [Set] button and change the properties as shown below.Note that other properties must be left unchanged.GeneralLabeln ,Monitor *1SettingsScreen No.2*1:Pressto set the label.(4) Resize the [Monitor] button larger than others.9-3-10Creating the Alarm ScreenCreate screen No.
4 (new screen) as the Alarm Screen.(1) Select [Screen] (menu bar) → [New].(2) At the screen selection dialog box, set “Standard Screen”.(3) At the new standard screen dialog box, set “4” for the screen No.Setting the screen properties(1) Select [Screen] (menu bar) → [Properties].(2) Set the screen properties as shown below for screen No. 4.405Creating the Sample DataSection 9-3AttributesScreen No.4HistorynTitleAlarm ScreenCommentAlarm ScreenBuzzerLoad Local 1 (Keyboard)System KeypadColourGridBackgroundBlackGrid SizeCustomHorizontal Spacing: 5Vertical Spacing:5Display GridnSnap to GridnCreating the screen title ([Alarm Screen])S Copying the screen title from screen No.
1 (Menu Screen)(1) Copy the “Menu Screen” character string and its frame (rectangle) onscreen No. 1 and paste them onto screen No. 4.(2) Adjust the display position of the pasted character string and frame to thedesired position.S Modifying to [Alarm Screen](3) Double click the “Menu Screen” (character) string and modify the propertiesas shown below. Note that other properties must be left unchanged.DescriptionAlarm Screen(4) Adjust the size of the frame (rectangle).Creating the alarm listS Setting the title(1) Select [Objects] (menu bar) → [Fixed Display] → [Text].406Creating the Sample DataSection 9-3(2) Click the mouse with the mouse cursor set at the position where the “AlarmList” (character) string is to be displayed (at the intended upper left corner oftext).(3) Set the properties as shown below.DescriptionAlarm ListPosition––Font TypeStandardScale1SmoothingnAttributeStandardColour1 (Equal)ForegroundWhiteBackgroundBlack(4) Adjust the position of the “Alarm List” (character) string on the data creationscreen by dragging it.S Creating the alarm list(5) Select [Objects] (menu bar) → [Alarm] → [List].
(Refer to 6-3-1 “Alarm List”.)(6) Click the mouse with the mouse cursor set at the position where the alarmlist is to be displayed (at the intended upper left corner).(7) Make the following settings in the dialog box for selecting whether or not theline scroll touch switches and page scroll touch switches are used.Create Line Scroll Touch SwitchnCreate Page Scroll Touch SwitchnReference: For NT31, NT31C, NT631, and NT631C, this dialog box is not displayed. Forthese models, create the alarm list and then set whether or not the line/page scrolltouch switches are created in the property settings.(8) Set the properties as shown below.407Creating the Sample DataSection 9-3GeneralPosition––Size––MessageColourLength32Display Line Qty8Scale1SmoothingnFrameWhiteBackgroundONWhiteOFFBlackImage & Library Display ImageLibColourSettingsList Settings2 (High)nForegroundWhiteBackgroundBlackStart Bit Table Entry0No. of Bits Referenced 8(9) Adjust the display position of the alarm list by dragging it.After that, click on any position in the screen other than the alarm list to cancel thealarm list selected state (edit state).S Changing the frame of the line scroll (down) touch switch(10) Specify the switch at the bottom in the touch switches at the right side of thealarm list and adjust its size and position (move it to the lowest line in thealarm list).(11) Double click the line scroll (down) touch switch and set the properties asshown below.408Creating the Sample DataSection 9-3GeneralPosition––Size––Labeln, <!FFF9>FramenShapeStandardShow ON StatenColourSettingsFrameWhiteONWhiteOFFTransparentFunction*1Input Key-ControlControl KeyLightFunctionAddressLamp Attribute*1:PC (PLC) Address––I/O Comments––GeneralLightHere, the label is not changed.
(If you need to change it, pressbutton.)After completing the setting, go to the next step without clicking onbut-ton.Reference: With NT31, NT31C, NT631, and NT631C, the touch switches used to control thealarm list are a part of the list and their properties, such as the label and the size,cannot be changed. Only the position can be adjusted.(12) Pressin the general property of a touch switch and set the labelproperties as shown below.Note that other properties must be left unchanged.Foreground ColorCyan(13) Adjust the position of the label graphic by dragging it.S Setting the page down, page up, and line scroll (up) touch switches(14) Modify the page down, page up, and line scroll (up) touch switches in thesame manner as the line scroll (down) touch switch.Refer to the screen in P?? to check the position of each touch switch.Modify the properties of the individual touch switches as shown below.409Creating the Sample DataSection 9-3GeneralSettingsPage downPage upScroll upPosition––––––Size––––––Labeln, <!FFF7> n, <!FFF6> n, <!FFF8>FramennnShapeStandardStandardStandardShow ON StatennnColourFrameWhiteWhiteWhiteONWhiteWhiteWhiteOFFTransparent Transparent TransparentFunctionInputInputInputKey-Control Key-Control Key-ControlControl KeyLightAddressFunctionLampAttributePC (PLC)Address––––––I/OComments––––––GeneralLightLightLight(15) Modify the foreground color of the label graphic to cyan as with the line scroll(down) touch switch.Reference: With NT31, NT31C, NT631, and NT631C, the touch switches used to control thealarm list can be adjusted only in position.Size, color, label can not be changed.
If you want to move the position, select [Edit](menu bar) → [Edit Object] (or right click → [Edit Object]) and specify the touchswitch.S Setting for the image/library data display field(16) Specify the alarm list and select [Edit] (menu bar) → [Edit Object].(17) Specify the image data display field, displayed at the central left part of thealarm list, and adjust the size and the position.(Resize the size to 200 X 200 dots.)410Creating the Sample DataSection 9-3Creating the [Menu] button, [Monitor] button, and [Set] buttonS Copying and pasting the buttons from screen No.
3(1) Copy the “Switch Screen” (character) string, frame (rectangle), [Menu] button, [Monitor] button, and [Alarm] button collectively and paste them ontoscreen No. 4.(2) Adjust the display position of the pasted (character) string, frame (rectangle), and buttons.S Modifying to the [Set] button(3) Double click the [Alarm] button and change the properties as shown below.GeneralLabeln ,Set *1SettingsScreen No.3*1:9-3-11Pressto set the label.Creating the Alarm List Library DataCreate the library data which is displayed at the occurrence of an alarm.Create the library data for FA20 to FA25. (For the library data creation procedure,refer to 8–2 “Library Editor”.)FA20Set line 1.FA21Set line 2.FA23FA24Check pipe andvalve.Detection nearentry.
Confirmsafety before restarting the line.FA22Check torquescrew.FA25Check the PC(PLC) and thenetwork.Reference: With NT31, NT31C, NT631, and NT631C, the library data codes are 1000 to 3FFF.411Creating the Sample DataSection 9-3S Creating the library data of code FA20(1) Select [Tools] (menu bar) → [Library Editor]..(2) Specify “FA20” in the library table and click on(3) Click the library creation area frame (dotted lines) which is displayed at theupper left area in the library creation screen and drag the point at the lowerright corner. The mouse cursor position is displayed under the screen;change the frame size to X=200, Y=200 (size: 200 200).(4) Select [Objects] (menu bar) → [Fixed Display] → [Text].(5) Click the mouse at the position where the (character) string is to be displayed (at the intended upper left corner of text).(6) Set the properties as shown below.DescriptionSet Line 1Position––Font TypeStandardScale1SmoothingnAttributeInverse FlashColour2 (High)ForegroundWhiteBackgroundBlack(7) Adjust the “Set Line 1” (character) string display position by dragging it.(8) After creating the library data of code FA20, clickat the upper rightsection in the FA20 library editor to close it.S Creating the library data of code FA21 to FA25.(9) Create the library data of code FA21 to code FA25 in the same manner.If (character) string occupies more than one line, create the (character)string line by line.Reference: It is possible to copy library data FA20 to other code so that it can be reused.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
