NT support tool (V053-E1-1) (986753), страница 48
Текст из файла (страница 48)
Note that the properties not shown here must be left unchanged.GeneralLabelLightFunctionsAddress*1:n, Lamp 2 *1PC (PLC) Bit AddressL0000001I/O CommentLamp 2Pressto set the label.If the I/O comment is already set for the PLC address of light function,clicking onbutton copies the label.(12) Create [Lamp 3], [Lamp 4], and [Lamp 5] in the same manner.(13) Modify the properties as shown below meeting the individual lamps.Lamp 3Generaln, LampLabel3*1LightAddress PC (PLC)L0000002FunctionsBit AddressI/OComment*1:Lamp 3n, Lamp 4n, Lampn, Lamp 5n, Lamp 5*1L0000003L0000004Lamp 4Lamp 5Pressto set the label.If the I/O comment is already set for the PLC address of light function,clicking onbutton copies the label.Creating the image/library lamp image dataCreate two kinds of image data for the image/library lamp.Create the image data for codes FE20 and FE21.3844*1Creating the Sample DataSection 9-3FE20FE21(1) Select [Tools] (menu bar) → [Image Editor].(2) Click on.(3) Set the properties as shown below and click onCodeSizeFE20Width64Height48Mode8 ColoursCompressionn(4) Click on.to create the image data.
(For the image data creationprocedure, refer to 8-1 “Image Editor”.)(5) Close the image editor.(6) Call the image editor again and create the image data for code FE21.Reference: It is possible to copy image data FE20 onto FE21 on the image table so that it canbe reused.Follow the procedure below.a. Click onand register the code FE21 (Properties other than codeneed not be changed).b. Specify FE20 and select [Copy] by pressingbutton.c. Specify FE21 and select [Paste] by pressingbutton.Creating the [Image Lamp]S Creating the title(1) Select [Objects] (menu bar) → [Fixed Display] → [Text].(2) Click the mouse with the mouse cursor set at the position where the label“Image Lamp” is to be displayed.(3) Set the properties as shown below.385Creating the Sample DataSection 9-3DescriptionImage LampPosition––Font TypeStandardScale2SmoothingnAttributeStandardColour2ForegroundWhiteBackgroundTransparent(4) Adjust the position of “Image Lamp” (character) string on the data creationscreen by dragging it.S Setting the image/library lamp(5) Select [Objects] (menu bar) → [Lamp] → [Image].(6) Click the mouse with the mouse cursor set at the position where the image/library lamp is to be displayed (at the intended upper left corner).(7) Set a check mark in the check box of the [Code] for OFF, in General, andclick on.(8) In the image table, specify “FE20” and click on.(9) Set a check mark in the check box of the [Code] for ON, in General, and clickon..(10) In the image table, specify “FE21” and click on(11) Set the lamp function properties as shown below.LightFunctionsAddressPC (PLC) Bit AddressL0000005I/O CommentImage Lamp(12) Adjust the display position of the image/library lamp.Reference: With NT31, NT31C, NT631, and NT631C, codes assigned to image data are from0001 to 0FFF.Creating [Bar Graph 1] and [Bar Graph 2]S Creating the title(1) Select [Objects] (menu bar) → [Fixed Display] → [Text].386Creating the Sample DataSection 9-3(2) Click the mouse with the mouse cursor set at the position where the character string of [Bar Graph 1] is to be displayed (at the intended upper left cornerof bar graph).(3)Set the properties as shown below.DescriptionBar Graph 1Position––Font TypeStandardScale1SmoothingnAttributeStandardColour2 (High)ForegroundWhiteBackgroundBlack(4) Adjust the position of “Bar Graph 1” (character) string on the data creationscreen by dragging it.S Creating the bar graph frame(5) Select [Objects] (menu bar) → [Graph] → [Bar Graph].
(Refer to 6-9-1 “BarGraph”.)(6) Drag the mouse cursor at the position where bar graph 1 is to be displayed(drag between diagonally opposing corners) to create the frame of [Bar Graph1].(7) Set the properties as shown below.GeneralPosition––Size––FramenDisplay SignnDirectionRightColourSettingsValue100%FrameWhite+ RangeWhite– RangeWhiteTable Entry4Display %nTable EntryDisplay %0%Table EntryDisplay %–100%n, 500n, 0Table EntryDisplay %n, –500387Creating the Sample DataSection 9-3S Setting the % display(8) After specifying the bar graph, select [Edit] (menu bar) → [Edit Object].(9) Double click on [0%] and set the properties as shown below.Position––Font TypeStandardScale1Smoothingn2 (High)Attribute––ColourForegroundWhiteBackgroundBlackS Adjusting the size and position of bar graph frame and % display(10) Specify [0%] at the upper left of the trend graph and drag it to the “%” displayposition.(11) Specify the bar graph frame and adjust the size and position of bar graphframe.S Creating bar graph 2(12) Specify all of label, bar graph frame, and % display of [Bar Graph 1] andcopy and paste them onto the data creation screen.(13) Move the pasted bar graph 1 element, which was pasted at the upper leftarea in the data creation screen, to the position of [Bar Graph 2].(14) Double click the label “Bar Graph 1”, which has been moved to the bar graph2 position, and modify the properties as shown below.LabelBar Graph 2(15) Double click on the frame of bar graph 2 and modify the properties as shownbelow.
Note that other properties must be left unchanged.SettingsValue100%Table Entry5Display %nTable EntryDisplay %0%Table EntryDisplay %–100%n, 0Table EntryDisplay %388n, 300n, –300Creating the Sample DataSection 9-3Creating the [Menu] button, [Set] button, and [Alarm] buttonS Creating the [Menu] button frame(1) Select [Objects] (menu bar) → [Touch Switch](2) Create the [Menu] button frame by dragging the mouse at the button displayposition.(3) Set the properties as shown below.GeneralPosition––Size––Labeln, Menu (refer tothe following) *1FramenShape3-DimensionShow ON StatenColourSettingsLightFunctionWhiteONWhiteOFFTransparentFunctionSwitch ScreenScreen No.1AddressLamp Attribute*1:FramePC (PLC) Address––I/O Comments––AttributeLightPressto set the label.After completing the setting, go to the next step without clicking onbutton.S Setting the label of [Menu] buttonin the general property of a touch switch and set the label(4) Pressproperties as shown below.389Creating the Sample DataSection 9-3DescriptionMenuPosition––Font TypeStandardScale11 (Equal)Smoothing––AttributeColourStandardForegroundWhiteBackgroundTransparentReference: With NT31, NT31C, NT631 and NT631C, “Colour: ON” and “Colour: OFF” can beset independently for a label so that the lamp can be displayed in different colors inthe ON and OFF states., (returns to touch switch property) then click onClick onagain.S Adjusting the size and position of the touch switch(5) Specify the [Menu] button and select [Edit] (menu bar) → [Edit Object].(6) Adjust the size and position of [Menu] button frame.(7) Adjust the position of label “Menu” by dragging it.S Creating the [Set] button(8) Copy the [Menu] button and paste it on the screen.(9) Move the [Menu] button pasted at the upper left area of the screen to the[Set] button position.(10) Double click the moved button and modify the properties as shown below.Note that other properties must be left unchanged.GeneralLabeln, Set *1SettingsScreen No.3*1:Pressto set the label.(11) Create the [Alarm] button in the same manner.Modify [Alarm] button properties as shown below.GeneralLabeln, Alarm *1SettingsScreen No.4*1:390Pressto set the label.Creating the Sample DataSection 9-3S Creating the frame(12) Select [Objects] (main menu) → [Fixed Display] → [Rectangle].(13) Drag the mouse so that the rectangular frame encloses the three buttons.(14) Use the properties as they are.(15) Adjust the size and the position of the frame (rectangle).S Setting the [Switch Screen] (character) string(16) Select [Objects] (main menu) → [Fixed Display] → [Text](17) Click the mouse with the mouse cursor set at the position where the [SwitchScreen] (character) string is to be displayed (at the intended upper left corner).(18) Set the properties as shown below.Switch ScreenDescriptionPosition––Font TypeStandardScale1SmoothingnAttributeStandardColour1 (Equal)ForegroundWhiteBackgroundBlack(19) Adjust the position of the “Switch Screen” (character) string on the data creation screen by dragging it.(20) Specify the “Switch Screen” (character) string, then select [Draw] (menubar) → [Bring to Front].
(For details of Moving an overlapped element to thefront or back, refer to 6-1-5 “Copying, Cutting, Pasting and Deleting Elements”.)The “Switch Screen” (character) string is brought to the front of the frame.Reference: The positional relationship in the display of the same kind of elements, such asamong fixed display elements, can be controlled by selecting [Draw] → [Bring toFront] or [Send to Back].391Creating the Sample Data9-3-8Section 9-3Creating the Monitor Screen (Parent Screen)Register screens No.