L101-E1-05A (986758), страница 2
Текст из файла (страница 2)
135 g, H5CX-A11@/-L8@: Approx. 105 gNote 1. The values are based on the set value.2. The value is applied for a minimum pulse width of 1 ms.3. To meet UL listing requirements with H5CX-L8@/-A11@ models, an OMRON P2CF-08-@ or P3G-08 Socket must be mounted on the Timer.Otherwise, H5CX-L8@/-A11@ models are considered to meet UL508 recognition requirements.4. The Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter are necessary to ensure IP66, NEMA4, and UL Type 4X waterproofing between the H5CX and installation panel.Multifunction Digital Timer H5CX-A/-L54Switching operations (× 10 )■ Life-test Curve (Reference Values)1,00050010030 VDC L/R=7 ms50250 VDC/3 0 VDCcosφ=110250 VAC cosφ=0.4012345Load current (A)Reference:A maximum current of 0.15 A can be switched at125 VDC (cosf=1) and a maximum current of 0.1 Acan be switched if L/R is 7 ms. In both cases, a life of100,000 operations can be expected.
The minimumapplicable load is 10 mA at 5 VDC (failure level: P).■ Inrush Current (Reference Values)VoltageApplied voltageInrush current(peak value)Time100 to 240 VAC264 VAC5.3 A0.4 ms24 VAC/12 to 24 VDC26.4 VAC6.4 A1.4 ms26.4 VDC4.4 A1.7 ms6Multifunction Digital TimerH5CX-A/-LConnections■ Block Diagram(Basic insulation)Power supplycircuitOutput circuit(See note.)(Basic insulation)Display circuitInternal controlcircuitInput circuitKey switchcircuitNote: Power circuit is not insulated from the input circuit, except for H5CX-A11/-A11S, which have basic insulation.■ I/O FunctionsInputsOutputsStart signalStops timing in A-2 and A-3 (power ON delay) modes.Starts timing in other modes.ResetResets present value.
(In elapsed time mode, the present value returns to 0; in remaining timemode, the present value returns to the set value.)Count inputs are not accepted and control output turns OFF while reset input is ON.Reset indicator is lit while reset input is ON.GateInhibits timer operation.Control output (OUT)Outputs take place according to designated operating mode when timer reaches corresponding setvalue.Multifunction Digital Timer H5CX-A/-L7■ Terminal ArrangementConfirm that the power supply meets specifications before use.6Unused7896GateInput use 0 VSignalGateSignalResetInput use 0 VResetH5CX-AS/-ASDH5CX-A/-AD789Unused1010Unused Unused UnusedUnused Unused Unused1112111211213133423455Transistor outputContact output(−)(−)(+)(+)The power supply and input circuit are not insulated.(See note 2.)Terminals 1 and 6 of the H5CX-AD are connected internally.The power supply and input circuit are not insulated.(See note 2.)Terminals 1 and 6 of the H5CX-ASD are connected internally.H5CX-A11S/-A11SDH5CX-A11/-A11DResetResetSignalSignalGateInternal circuitGateInternal circuit5 6 75 6 7Unused48Unused40V39100V321 1182Contact outputUnused1 11910Transistor outputUnused(−) (+)(−) (+)The power supply and input circuit of theH5CX-A11 have basic insulation.The power supply and input circuit of theH5CX-A11D are not insulated.
(See note 2.)Terminals 2 and 3 of the H5CX-A11D areconnected internally.The power supply and input circuit of theH5CX-A11S have basic insulation.The power supply and input circuit of theH5CX-A11SD are not insulated. (See note 2.)Terminals 2 and 3 of the H5CX-A11SD areconnected internally.H5CX-L8S/-L8SDH5CX-L8/-L8DInternal circuitInternal circuitSignalResetSignal436721Unused5ResetContact output845367210VTransistor output80V(−) (+)(−) (+)The power supply and input circuit arenot insulated. (See note 2.)Terminals 1 and 2 of the H5CX-L8D areconnected internally.The power supply and input circuit arenot insulated.
(See note 2.)Terminals 1 and 2 of the H5CX-L8SDare connected internally.Note 1. Do not connect unused terminals as relay terminals.2. The power supply and input circuit are not insulated, so unwanted current from the AC power supply may burn out internal parts. Refer toSafety Precautions (H5CX-A/-L) on page 49 for wiring details.8Multifunction Digital TimerH5CX-A/-L■ Input CircuitsSignal, Reset, and Gate Input+14 V1 kΩINInternal circuitNote: When using no-voltage input (NPN input).■ Input ConnectionsThe inputs of the H5CX-A@/-A11@ are no-voltage (short-circuit or open) inputs or voltage inputs.The input of the H5CX-L8@ is no-voltage input only.Note: Power circuit is not insulated from the input circuit, except for H5CX-A11/-A11S, which have basic insulation.
For wiring, refer to Safety Precautions (H5CX-A/-L) on page 49.No-voltage Inputs (NPN Inputs)Contact InputOpen CollectorVoltage Output(Connection to NPN opencollector output sensor)(Connection to a voltage outputsensor)PC or sensorDC Two-wire SensorH5CX-A@H5CX-A11@H5CX-L8@H5CX-A@H5CX-A11@H5CX-L8@Operate with transistor ONOperate with transistor ONH5CX-A@H5CX-A11@H5CX-L8@H5CX-A@H5CX-A11@H5CX-L8@Operate with relay ONOperate with transistor ONGate inputSignal inputInput0VReset inputGate inputSignal inputInput0VReset inputGate inputSignal inputInput0VReset inputGate inputSignal inputInput0VReset inputSensorNo-voltage Input Signal LevelsApplicable Two-wire SensorNo-contact inputLeakage current:Switching capacity:Residual voltage:Operating voltage:Short-circuit levelTransistor ONResidual voltage: 3 V max.Impedance when ON: 1 kW max.(the leakage current is 5 to 20 mA when theimpedance is 0 W)1.5 mA max.5 mA min.3.0 VDC max.10 VDCOpen levelTransistor OFFImpedance when OFF: 100 kW min.Contact inputUse contact which can adequately switch5 mA at 10 VNote: The DC voltage must be 30 VDC max.Multifunction Digital Timer H5CX-A/-L9Voltage Inputs (PNP Inputs)No-contact Input(NPN Transistor)No-contact Input(PNP Transistor)(Connection to NPN opencollector output sensor)(Connection to PNP opencollector output sensor)H5CX-A@H5CX-A11@H5CX-A@H5CX-A11@Operate with transistor ONOperate with transistor OFFVoltage Input Signal LevelsHigh level (Input ON):Low level (Input OFF):Input resistance:4.5 to 30 VDC0 to 2 VDCApprox.
4.7 kWNote: The DC voltage must be 30 VDC max.Multifunction Digital TimerH5CX-A/-LH5CX-A@H5CX-A11@Operate with relay ONGate inputSignal inputInput0VReset inputGate inputInput0VReset inputGate inputSignal inputInputReset input0VSignal inputSensorSensor10Contact InputNomenclatureOperation KeyIndicatorMode Key(Changes modes and setting items)Reset Indicator (orange)Key Protection Indicator (orange)Reset Key(Resets present value and output)Control Output Indicator (orange)Present Value(red or green (programmable) forH5CX-A models, red for H5CX-A11/-L models)Character height: 11.5 mmTime Unit Display(Color is same as present value.):(If the time range is 0 min, 0 h, 0.0 h,or 0 h 0 min, this display flashes toindicate timing operation.)Up Keys 1 to 4Down Keys 1 to 4Front ViewFront color: BlackSwitchesKey-protect Switch(Default setting) OFFONSet Value (green)Character height: 6 mmSet Value 1, 2 DisplayDIP SwitchCase color: Black12345678ONOFFNote 1: All the pins are factory-set to OFF.2: There is no DIP switch on the H5CX-L8@.Multifunction Digital Timer H5CX-A/-L11DimensionsNote: All units are in millimeters unless otherwise indicated.■ Dimensions without Flush Mounting AdapterH5CX-A/-AS (Flush Mounting Models)48x48610044.8x44.8Note:M3.5 terminal screw (effective length: 6 mm)H5CX-AD/-ASD (Flush Mounting Models)48x4866444.8x44.8Note:M3.5 terminal screw (effective length: 6 mm)H5CX-A11/-A11S (Flush Mounting/Surface Mounting Models)48x48614.472.544.8x44.8H5CX-A11D/-A11SD (Flush Mounting/Surface Mounting Models)448x488663.714.4H5CX-A11D44.8x44.8H5CX-L8@ (Flush Mounting/Surface Mounting Models)448x488663.714.344.8x44.812Multifunction Digital TimerH5CX-A/-L■ Dimensions with Flush Mounting AdapterH5CX-A/-AS (Provided with Adapter and Waterproof Packing)Y92S-29 (provided)Waterproof PackingPanelY92F-30 (provided)Flush Mounting Adapter(51)58487.598.5H5CX-AD/-ASD (Provided with Adapter and Waterproof Packing)Y92S-29 (provided)Waterproof Packing58PanelY92F-30 (provided)Flush Mounting Adapter(51)Panel CutoutsPanel cutouts areasshown below.(according to DIN43700).487.562.560 min.45 +0.6−0H5CX-A11/-A11S (Adapter and Waterproof Packing Ordered Separately)Y92S-29 (order separately)Waterproof Packing58Panel45 +0.6−0Y92F-30 (order separately)Flush Mounting Adapter60 min.
15 min.P3GA-11(order separately)Rear SurfaceConnectionSocket(51)487.598.7H5CX-A11D/-A11SD (Adapter and Waterproof Packing Ordered Separately)Y92S-29 (order separately)Waterproof PackingNote 1. The mounting panel thicknessshould be 1 to 5 mm.2. To allow easier operability, it isrecommended that Adapters aremounted so that the gap betweensides with hooks is at least 15 mm.3. It is possible to mount timers sideby side, but only in the directionwithout the hooks.PanelY92F-30 (order separately)Flush Mounting Adaptern side by side mountingP3GA-11(order separately)Rear SurfaceConnectionSocket(51)58AA = (48n − 2.5) +10With Y92A-48F1 attached.A = {48n−2.5 + (n−1) x 4} +1048With Y92A-48 attached.A = (51n−5.5) +1089.97.5H5CX-L8@ (Adapter and Waterproof Packing Ordered Separately)Y92S-29 (order separately)Waterproof Packing)PanelY92F-30 (order separately)Flush Mounting AdapterP3GA-11(order separately)Rear SurfaceConnectionSocket58(51)487.584.8Multifunction Digital Timer H5CX-A/-L13■ Dimensions with Front Connecting Socket112H5CXA11/A11S109.7103.2H5CXA11D/A11SDL8@100.9P2CF-08-@P2CF-11-@P2CF-11-@9092.3Note: These dimensions vary with the kind of DIN track (reference value).■ Accessories (Order Separately)Note: All units are in millimeters unless otherwise indicated.Track Mounting/Front Connecting SocketP2CF-08Eight,M3.5 x 7.5 sems7.84.5370 max.35.4Two, 4.5 dia.holesTerminal Arrangement/Internal Connections(Top View)Surface Mounting Holes450 max.Two, 4.5 dia.
or two, M420.3 max.P2CF-08-E (Finger Safe Terminal Type)Conforming to VDE0106/P10040±0.2Eight,M3.5 x 7.5 sems4.557.831.370 max.35.4Two, 4.5 dia.holes440±0.21950 max.20.321.5 max.14Multifunction Digital TimerH5CX-A/-LTrack Mounting/Front Connecting SocketP2CF-11Eleven,M3.5 x 7.5 sems7.834.570 max.Terminal Arrangement/Internal Connections(Top View)35.4Two, 4.5 dia.holesSurface Mounting HolesTwo, 4.5 dia.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
