NT support tool (V053-E1-1) (986753), страница 61
Текст из файла (страница 61)
It is not permissible to install the system program of another PTmodel.Reference: The Support Tool is provided with the system programs of the following PT models.NT31, NT31C, NT631, NT631C with “-V1” (system program Ver.2.1),NT11S (For SYSMAC and multivendor)The system program must be installed with the system installer when installingthe Support Tool at your personal computer. For details of installation at the personal computer, refer to Section 2 “Setting Up the Support Tool”.
System programs of NT30, NT30C, NT620S, NT620C/NT625C are availableupon request. To install these system programs, purchase the following systeminstaller separately.NT30-ZS3AT-EV1:For NT30/NT30CFor SYSMACNT620-ZS3AT-EV1 :For NT620S/NT620C/NT625CFor SYSMACNT620-ZS3AT-EMV1 :For NT620S/NT620C/NT625CFor multivendorThese system programs can be transmitted to a PT using the system installersupplied with the Support Tool (Ver.3.2).490System Installer OperationAppendix BStarting and Exiting the System InstallerThe system installer is started by pressing the Windows start button, then selecting[Programs] → [Omron] → [Ntst3.2] → [NT–series System Installer] as shownbelow.e.g.) Windows 95When the system installer starts, the main window, shown below, is displayed.Existing the system installerYou can exit the system installer by using any of the following operations: Select [Download System] → [Exit].
Click on thebutton in the upper right section of the main window. Double click on the system installer icon in the upper left section of the main window. Click on the system installer icon in the upper left section of the main window,then select [Close] in the control menu box. Press the [F4] key while holding down the [Alt] key.When you exit the system installer, the Windows screen is displayed.491System Installer OperationAppendix BFunctions of the Main WindowThe functions provided by the main window of the system installer are describedbelow.Drive:Specify the drive where the system program is stored.
Click onand select thedrive name from the displayed items.The drive in the network can be selected only when it is allocated to “My Computer”.PT Model:Specify the PT model for which the system program is installed. Click onandselect the drive name from the displayed items.Select NT31, NT31C, NT631 or NT631C to use NT31, NT631C, NT631 orNT631C with “-V1”.Com Port:Specify the port used for communications with the PT. Click onand select thedrive name from the displayed items.
Selection is possible from [COM1] and[COM2].Look in:Specify the folder where the system program is stored. The folder can beopened or closed by double clicking on the folder line.Among the folders which are open, the folder at the bottom line is selected.492System Installer OperationAppendix BSystem File(s):The system programs in the specified folder and those for the specified PT model are displayed. Specify the system program which is to be installed at the PTfrom among the displayed programs. The extension of a system program filename represents the PT model.ExtensionPT Model.31NT31.31CNT31C.631NT631.63CNT631C.11SNT11S:The system program is installed when this button is clicked.493System Installer OperationAppendix BInstalling the System ProgramThe procedure for installing the system program is shown below.(1) Specify the PT model for which the system program is installed for [PT Model]in the main window.(2) Specify the system program to be installed by setting the information at[Drive], [Look in], and [System File(s)] in the main window.(3) Specify the RS-232C port used for the communications with the PT for [ComPort].(4) Make the PT ready for installation of the system program.The operation required at the PT varies depending on the PT model.
Basically, execute the processing for deleting the system program, then that for setting the PT in the state in which it waits for the reception of the system program. For details, refer to the manual for your PT.(5) Click onin the main window.The system program is installed.While the system program is being installed, the progress of the operation isdisplayed in graph form.(6) At the completion of system program installation, the corresponding messageis displayed.Read the message and click on.(7) At the PT, press the touch switch which acknowledges the end of system program installation.The PT re-starts by the installed system program.494NT Transfer UtilityAppendix CAPPENDIX CNT Transfer UtilityWith the Support Tool on CD–ROM, the “NT Transfer Utility” which can transmitscreen data to a PT easily on site is supplied.It can download the screen data file in mmi format to a PT and can save the screendata uploaded from a PT to a file in mmi format.Screen data file in mmi format is less than 1.44 Mbytes.
So it is useful when yousave the file in a floppy disk to transfer the data to and from a PT on site.Reference: NT Transfer Utility is a software which is exclusively used for downloading/uploading the screen data without modifying the contents. NT Transfer Utility can handle only the file in mmi format. It is not possible to reador write the file in onw format which is a standard format of the Support Tool.Therefore, please be sure to save the screen data in mmi format when you usethe NT Transfer Utility.
For details of the restriction of the file types and mmi format, refer to 3–3–3 “Saving the Screen Data (Application) File” NT Transfer utility downloads/uploads the screen data in the application unit. It isnot possible to perform individual transmission such as the transmission in thescreen unit.Equipment necessary for using the NT Transfer UtilityThe following indicates the equipment necessary for using the Support Tool.Hardware Recommended CPUPentium 100MHz or faster CPU Personal ComputerUse an IBM personal computer or 100% compatible.
Recommended Memory32 Mbytes minimum Free Area in Hard DiskAt least 3.5 MbytesOperating SystemMicrosoft Windows 95/98 and Windows NT (Windows NT is only available withNT–series Support Tool Ver.3.3 onward.)Device necessary for transmitting screen data RS–232C cableThe cable used for the Support Tool can be used.For cable specifications, refer to Appendix I “Connecting Cable Specifications”.495NT Transfer UtilityAppendix CInstalling the NT Transfer UtilityInstall the NT Transfer Utility in a personal computer which is to be connected to aPT on site.
NT Transfer utility operates alone. You do not need to pre–install theSupport Tool in the personal computer.Before installingTo install the NT Transfer Utility in the personal computer without a CD–ROM drive,make the floppy disks for installation beforehand following the procedure below. Equipment to prepare2 floppy disks (3.5 inch 1.44Mbytes 2HD, formatted) Creating installation FDCopy the contents in the following folder of the Support Tool (CD–ROM) to FDs.– The contents of [disk1] folder in [Transfer Utility] folder→ To the first installation disk– The contents of [disk2] folder in [Transfer Utility] folder→ To the second installation diskReference: If the personal computer has a CD–ROM drive, the install program can be executed from the CD–ROM of Support Tool directly.InstallationTo install the NT Transfer Utility, execute the install program which has been readyin your software package.Reference: The basic operation of the install program is same as the install program of theSupport Tool.
Refer to 2–2–1 “Basic Installation Operation”. Procedure(1) Start up Windows 95/98(2) If your media is FD, set the first FD of the system disks in drive A (or other 3.5inch FD drive)If you are using CD–ROM, set the Support Tool CD–ROM in the CD–ROMdrive while holding down the Shift key to prevent the Support Tool setup program from starting up.
(Release the Shift key after CD–ROM is recognizedand the access to the CD–ROM is stopped.) If the Support Tool setup programis automatically started, click onto abort it.Reference: You can execute the setup program by double clicking “Setup.exe” for NT TransferUtility in the Support Tool system disk by displaying the “Explorer” of Windows95/98. In this case, steps 3, 4 and 5 bellow can be skipped.496NT Transfer UtilityAppendix C(3) Click on the Start button of Windows 95/98 and select “Run...”.(4) Input “a:\setup” in the input field in the specified window.Note that drive designation must agree with the name of the drive where youset the system disk.
If you set the disk in drive B, input “b: \ setup”. In case ofCD–ROM, click onand specify the “SETUP.EXE” in the “disk1” folder in the “Transfer Utility” folder.(5) Click on.The installation started.(6) When the setup screen of the NT Transfer Utility is displayed, click on.The screen for specifying the destination of program installation is displayed.(7) Specify the directory for installation.In the initial state, the directory shown below is set as the destination directory.C: \Program Files\Omron\Ntst3.2\Transfer UtilityIf you want to change the directory, click onand input the drive anddirectory.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
