M070-04 (986759), страница 3
Текст из файла (страница 3)
(See note 1.)Counting cannot be performed during reset/reset 1 input.The reset indicator is lit during reset input.• When used as a dual counterResets the CP1 present value (to 0).Counting for CP1 input cannot be performed during reset 1 input.The reset indicator is lit during reset 1 input.Total Reset orReset 2(See note 2.)• When used as a 1-stage/2-stage counterDoes not operate (Not used).• When used as a total and preset counterResets the total count value.Holds the total count value at 0 during total reset input.• When used as a batch counterResets the batch count value and batch output (OUT1).Holds the batch count value at 0 during reset 2 input.• When used as a dual counterResets the CP2 present value.Counting for CP2 input cannot be performed during reset 2 input.OUT1, OUT2Outputs take place according to designated output mode when corresponding preset is reached.Note: 1.
In increment mode or increment/decrement mode, the present value returns to 0; in decrement mode, the present value returns to theset value with 1-stage models, and returns to set value 2 with 2-stage models.2. The reset indicator will not be lit when the total reset or reset 2 input is ON.Using as a TachometerInputsOutputs8CP1, CP2Reads counting signals. (CP2 input is not available.)Reset 1, Reset 2Holds the measurement value and outputs. (Reset 2 input is not available.)The reset indicator is lit during hold.OUT1, OUT2Outputs signals according to the specified output mode when a set value is reached.Multifunction Preset Counter H7CX-A■ Terminal ArrangementConfirm that the power supply meets specifications before use.Total reset6CP110CP2CP1Total resetCP2Reset0VResetH7CX-AD/-A4D1-stage Contact OutputH7CX-A/-A41-stage Contact Output789100V6(−)789Sensor, etc.Unused(+) 12 VDC11Unused12Unused131151UnusedUnused1213External powersupply12342345OUTOUT(−)(+)Note: Terminals 1 and 6 are connected internally.CP16Total reset10CP20VResetH7CX-ASD/-A4SD1-stage Transistor OutputTotal resetCP1CP2ResetH7CX-AS/-A4S1-stage Transistor Output789100V6(−)789Sensor, etc.Unused(+) 12 VDC11Unused12Unused131151UnusedUnused1213External powersupply1234234OUT5OUT(−)(+)Note: Terminals 1 and 6 are connected internally.H7CX-A11/-A114/-A11D1/-A114D11-stage Contact OutputH7CX-A11S/-A114S/-A11SD11-stage Transistor OutputResetResetCP1CP1Internal circuitCP20V(−)(+)489101 11Internal circuit5 6 7Total reset32Sensor, etc.CP25 6 7Total reset0V(−)(+)89102Sensor, etc.12 VDC431 1112 VDCExternal power supplyExternal power supplyOUTOUT(−)(+)(−)(+)Note: Do not connect unused terminals as relay terminals.Multifunction Preset CounterH7CX-A910CP19Reset 28CP2CP1Reset 27789100V0V6(−)Reset 1CP2H7CX-AWS/-AWSD12-stage Transistor OutputReset 1H7CX-AW/-A4W/-AWD12-stage Contact Output6(−)Sensor, etc.Sensor, etc.(+)(+) 12 VDCExternal powersupply11121312 VDC11OUT11213OUT1External powersupply123415235(−)(+)910CP18Reset 2CP1Reset 27CP2CP2H7CX-AUSD11 or 2-stage Transistor OutputReset 1H7CX-AWSD/-A4WSD2-stage Transistor Output(+)Reset 1(−)4OUT2OUT2789100V0V66(−)Sensor, etc.Unused(+)11121312 VDC11OUT11213OUT1 or 2External powersupply12345123(−)(+)Note: Each output can be flexibly allocated toeither stage 1 or 2 in function selectionmode.Reset 1CP2CP1Reset 2H7CX-AU/-AUD11-stage Contact, 1-stage Transistor Output789100V6Sensor, etc.(+)12 VDCExternal powersupply1112123134OUT1 or 25OUT 1 or 2(−)(+)Note: Each output can be flexibly allocated to eitherstage 1 or 2 by setting in function selection mode.■ Input CircuitsCP1, CP2, Reset/Reset 1, and Total Reset/Reset 2 Input+14 V1 kΩINInternalcircuitNote: The circuit shown above is for no-voltage input (NPN input).105(+)(−)Note: 1.
Terminals 1 and 6 are connected internally.2. Do not connect unused terminals as relay terminals.(−)4OUT 1 or 2OUT2Multifunction Preset Counter H7CX-A■ Input ConnectionsThe inputs of the H7CX are no-voltage (short-circuit or open) inputs or voltage inputs.When using as a tachometer, CP2 input and total reset/reset 2 input are not available.No-voltage Inputs (NPN Inputs)Open CollectorVoltage Output67891037564H7CX-A@H7CX-A11@67891037564H7CX-A@H7CX-A11@67891037564H7CX-A@H7CX-A11@Total reset/reset 2 inputCP1 inputCP2 inputReset/reset 1 inputInputCP1 inputCP2 inputInputReset/reset 1 input0V67891037564Operates when the transistor turns ON.Operates when the contact turns ON.Operates when the transistor turns ON.Operates when the transistor turns ON.Total reset/reset 2 inputTotal reset/reset 2 inputCP1 inputCP2 inputReset/reset 1 input0VInputCP1 inputCP2 inputInputReset/reset 1 input0VH7CX-A@H7CX-A11@DC Two-wire SensorSensorTotal reset/reset 2 inputPLC orsensorContact InputNo-voltage Input Signal LevelsApplicable Two-wire SensorNo-contact inputLeakage current: 1.5 mA max.Switching capacity: 5 mA min.Residual voltage: 3 VDC max.Operating voltage: 10 VDCShort-circuit levelTransistor ONResidual voltage: 3 V max.Impedance when ON: 1 kΩ max.(The leakage current is 5 to 20 mA when theimpedance is 0 Ω.)Open levelTransistor OFFImpedance when OFF: 100 kΩ min.Contact inputUse contact which can adequately switch5 mA at 10 V.Maximum applicable voltage: 30 VDC max.Voltage Inputs (PNP Inputs)No-contact Input(NPN Transistor)67891037564H7CX-A@H7CX-A11@67891037564Operates when the transistor turns ON.Operates when the transistor turns OFF.H7CX-A@H7CX-A11@Total reset/reset 2 inputCP1 inputCP2 inputReset/reset 1 input0VInputCP1 inputCP2 inputReset/reset 1 input0VInputCP1 inputCP2 inputInputReset/reset 1 input0VTotal reset/reset 2 inputSensorTotal reset/reset 2 inputSensorH7CX-A@H7CX-A11@Contact InputNo-contact Input(PNP Transistor)67891037564Operates when the contact turns ON.Voltage Input Signal LevelsHigh level (Input ON):Low level (Input OFF):Maximum applicable voltage:Input resistance:4.5 to 30 VDC0 to 2 VDC30 VDC max.Approx.
4.7 kΩMultifunction Preset CounterH7CX-A11NomenclatureIndicatorsA Reset Indicator (Orange)Lit when the reset input (1) or reset keyis ON.B Key Protection Indicator (Orange)C Control Output Indicator (Orange)OUT:One stageOUT1, OUT2: Two stagesD Total Count IndicatorLit when the total count value isdisplayed.E Batch IndicatorLit when the batch count value isdisplayed.F Set Value 1, 2 Stage IndicatorG Present Value (Main Display)Character height: 11.5 mm (6-digit: 9mm)H Set Value (Sub-display)Character height: 6 mmOperation Keys127345691110128Front view of 4-digit modelI Mode KeyUsed to switch mode and setting items.J Reset KeyThe operation of the reset functiondepends on the configuration selectedas shown in the table below.K Up Keys: 1 to 4(6-digit models: 1 to 6)L Down Keys: 1 to 4SwitchesM Key Protect Switch1(Factory setting) OFF2734568ONDIP Switch91110Front view of 6-digit model1314Reset Operation by Reset KeyConfiguration1-stage/2-stagecounterReset operationResets the present value and outputs.Total and preset • Resets the present value and outputs.counter• When the total count value is displayed, resetsthe present value, the total count value, andoutputs.12Multifunction Preset Counter H7CX-ABatch counter• Resets the present value and OUT2.• When the batch count value is displayed,resets the present value, the batch countvalue, and outputs.Dual counterResets the CP1 present value, CP2 present value, dual count value, and outputs.TachometerMaintains the measured value and outputs (holdfunction).DimensionsNote: All units are in millimeters unless otherwise indicated.■ Counter (without Flush Mounting Adapter)Screw-terminal Models with External Power Supplies (Flush Mounting)• H7CX-A• H7CX-AS• H7CX-A4• H7CX-A4S• H7CX-AW• H7CX-AWS• H7CX-A4W• H7CX-AWD1• H7CX-AWSD1• H7CX-AU• H7CX-AUD1• H7CX-AUSD148×48610044.8×44.8Note: M3.5 terminal screw (effective length: 6 mm)Screw-terminal Models without External Power Supplies (Flush Mounting)• H7CX-AD• H7CX-ASD• H7CX-A4D• H7CX-A4SD• H7CX-AWSD• H7CX-AWSD48×4866444.8×44.8Note: M3.5 terminal screw (effective length: 6 mm)11-pin Socket Models (Flush Mounting/Surface Mounting)• H7CX-A11• H7CX-A11S• H7CX-A11D1• H7CX-A11SD1• H7CX-A114• H7CX-A114S• H7CX-A114D148×48672.514.444.8×44.8Multifunction Preset CounterH7CX-A13■ Dimensions with Flush Mounting AdapterScrew-terminal Models with External Power Supplies(Provided with Adapter and Waterproof Packing)Panel Cutouts• H7CX-A• H7CX-AS• H7CX-A4• H7CX-A4SPanel cutouts are asshown below.(according to DIN43700).• H7CX-AW• H7CX-AWS• H7CX-A4W• H7CX-AWD1• H7CX-AWSD1• H7CX-AU• H7CX-AUD1• H7CX-AUSD1Y92S-29 (provided)Waterproof PackingPanel60 min.Y92F-30 (provided)Flush Mounting Adapter45+0.6−045+0.6−060 min.
15 min.(51)58487.598.5Screw-terminal Models without External Power Supplies(Provided with Adapter and Waterproof Packing)• H7CX-AD• H7CX-ASD• H7CX-A4D• H7CX-A4SD• H7CX-AWSD• H7CX-A4WSDY92S-29 (provided)Waterproof Packing58Panel Y92F-30 (provided)Flush Mounting AdapterNote: 1. The mounting panel thicknessshould be 1 to 5 mm.2. To allow easier operability, it isrecommended that Adapters aremounted so that the gap betweensides with hooks is at least 15 mm(i.e., so that the panel cutout intervalis at least 60 mm).3. It is possible to mount countersside by side, but only in thedirection without the hooks.If they are mounted side-by-side,water-resistant specificationscannot be ensured.(51)n side by side mountingA48A = (48n − 2.5)+1062.57.511-pin Socket ModelsWith Y92A-48F1 attached.A = {48n−2.5 + (n−1) x 4}+10(Adapter and Waterproof Packing Ordered Separately)• H7CX-A11• H7CX-A11S• H7CX-A11D1• H7CX-A11SD1• H7CX-A114• H7CX-A114S• H7CX-A114D1With Y92A-48 attached.A = (51n−5.5)+10Y92S-29 (order separately)Waterproof Packing58Panel Y92F-30 (order separately)Flush Mounting AdapterP3GA-11(order separately)Back ConnectingSocket(51)487.598.7■ Dimensions with Front Connecting SocketH7CX-A11@109.7112P2CF-11Note: These dimensions vary with the kind of DIN track (reference value).14Multifunction Preset Counter H7CX-A■ Accessories (Order Separately)Note: All units are in millimeters unless otherwise indicated.Track Mounting/Front Connecting SocketP2CF-11Eleven,7.8M3.5 x 7.5 sems34.570 max.Terminal Arrangement/Internal Connections(Top View)35.4Two, 4.5-dia.holesSurface Mounting HolesTwo, 4.5 dia.
or two, M4450 max.31.2 max.40±0.2Note: Track mounting is also possible.P2CF-11-E (Finger-safe Terminal Type)Conforming to VDE0106/P100Eleven,M3.5 x 7.5 sems4.557.831.270 max.35.4Two, 4.5-dia.holes440±0.250 max.3031.2 max.Back Connecting SocketP3GA-11Terminal Arrangement/Internal Connections(Bottom View)27 dia.4525.6454.56.216.3Note: Finger protection can be ensured by using in combination with the Y92A-48G Terminal Cover.Finger-safe Terminal CoverConforming to VDE0106/P100Y92A-48G(Attachment for P3GA-11Socket)Twelve, 6.4-dia. holes3447.7 x 47.716.548 x 4824.6 27.647.4Multifunction Preset CounterH7CX-A15Hard CoverY92A-48Note: 1.
Depending on the operating environment, the condition ofresin products may deteriorate, and may shrink or becomeharder. Therefore, it is recommended that resin productsare replaced regularly.2. The H7CX’s panel surface is water-resistive (conforming toIP66) and so even if drops of water penetrate the gaps between the keys, there will be no adverse effect on internalcircuits. If, however, there is a possibility of oil being presenton the operator’s hands, use the Soft Cover. The Soft Coverensures protection equivalent to IP54F against oil.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
