M070-04 (986759), страница 4
Текст из файла (страница 4)
Do not,however, use the H7CX in locations where it would come indirect contact with oil.Soft CoverY92A-48F1Flush Mounting Adapter(provided with screw-terminal models)Waterproof Packing(provided with screw-terminal models)Y92F-30Y92S-29When using the Y92S-29, the degree of protection for the H7CX'spanel surface conforms to NEMA4, UL Type 4X, and IP66. (Depending on the operating environment, the condition of the panel maydeteriorate, shrink, or become harder. Therefore, regular replacement is recommended.)Mounting TrackPFP-100N, PFP-50NPFP-100N2167.3±0.154.54.515 25251035±0.327±0.1535±0.325 *251,000 (500) 10(See note.)1512525 152525101,0002724110Note: The values shown in parentheses are for the PFP-50N.End PlatePFP-MSpacerPFP-S106.2161251.81501.811.51610 M4 x 8pan headscrew35.5 35.334.844.31.34.8Multifunction Preset Counter H7CX-A16.529.21.5Operating Procedures■ Setting Procedure GuideSetting for Counter Operation(1-stage/2-stage Counter, Total and Preset Counter, Batch Counter, Dual Counter)When Using Basic Settings OnlyThe settings can be performed easily with the DIP switch.➡ For details on the setting methods, refer to page 18.Basic Settings••••••Counting speed (30 Hz, 5 kHz)Input mode (UP, DOWN)Output mode (N, F, C, K-1)One-shot output time (0.5 s, 0.05 s)(See note 2.)Reset input signal width (20 ms, 1 ms)NPN/PNP input mode (NPN, PNP)When Using Settings Other than the AboveAll the functions can be set with the operation keys.➡ For details on the setting methods, refer to page 19.Other Settings12345678ONOFFWhen Using Advanced FunctionsSettings for advanced functions other than the basicsettings above can be performed with the operation keys.➡ For details on the setting methods, refer to page 19.Advanced Functions• Input mode (UP/DOWN A, UP/DOWN B, UP/DOWN C)• Output mode (R, P, Q, A, K-2, D, L, H)• One-shot output time (except for 0.5 s and 0.05 s) (See note 2.)•••••••Dual count calculating modeOutput 1 time (for 2-stage counter)Decimal point positionPrescale valueDisplay colorOutput allocationKey protect levelNote: 1.
At the time of delivery, the H7CX is set to the 1-stage counter (2-stage counter for H7CX-AW@/-A4W@ models) configuration.2. Set to output 2 time when using as a 2-stage counter or batch counter.Setting for Tachometer OperationWhen Using Basic Settings OnlyThe settings can be performed easily with the DIP switch.➡ For details on the setting methods, refer to page 30.Basic Settings••••Counting speed (30 Hz, 10 kHz)Output mode (HI-LO, AREA, HI-HI, LO-LO)Average processing (OFF, 2, 4, 8 times)NPN/PNP input mode (NPN, PNP)12345678ONOFFWhen Using Advanced FunctionsSettings for advanced functions other than the basicsettings above can be performed with the operation keys.➡ For details on the setting methods, refer to page 31.Advanced Functions•••••••Decimal point positionPrescale valueAuto-zero timeStartup timeDisplay colorOutput allocationKey protect levelNote: At the time of delivery, the H7CX is set to the 2-stage counter (1-stage counter for H7CX-AU@ models) configuration.Multifunction Preset CounterH7CX-A17■ Operating Procedures (Counter Function)Settings for Basic OperationsSettings for basic functions can be performed with just the DIP switch.Be sure to set pin 1 to ON.12345678ONOFFNote: All of the pins are factory-set to OFF.Item1DIP switch settings enable/disable234OFFONDisabledEnabledCounting speed30 Hz5 kHzInput modeUP (increment) DOWN (decrement)Output modeRefer to the table on the right.Pin 4Pin 5OFF56One-shot output time(See note.)0.5 s0.05 s7Reset input signal width20 ms1 ms8NPN/PNP input modeNPNPNPOutput modeOFFNONOFFFOFFONCONONK-1Note: Set to one-shot output 2 time when using as a 2-stage counteror batch counter.Easy Confirmation of Switch Settings Using IndicatorsThe ON/OFF status of the DIP switch pins can beconfirmed using the front display.
For details, refer to page 36.Note: 1. Be sure to set pin 1 of the DIP switch to ON. If it is set to OFF, the DIP switch settings will not be enabled.2. Changes to DIP switch settings are enabled when the power is turned ON.3. When setting input modes, output modes, or output times that cannot be set with the DIP switch, all of the settings have to be made usingthe operation keys. For details on the setting methods, refer to page 19. When making settings using the operation keys, be sure to setpin 1 of the DIP switch to OFF.Switching to Total and Preset Counter, Batch Counter, and Dual Counter Operation (See note.)The H7CX is factory-set to the 1-stagecounter (2-stage counter for H7CX-AW@/A4W@ models) configuration. To change toa different configuration, use the procedureshown on the right. For details, refer topage 36.Power ONConfiguration selection modeNote: This includes changing to the 2stage counter (or 1-stage counter)configuration.MODE+Run mode1Hold down for1 s min.
(See note.)Note: The MODE key must be pressed before theSelect the configuration using the(1-stagecounter)(2-stage (Total andcounter) preset counter)andkeys ((Batchcounter)1key.key with 6-digit models).(Dualcounter)(Tachometer)Note: The configurations that can be selected vary with the model.Advanced-Function SettingsAfter making DIP switch settings for basic operations, advanced functions (see note) can be added using the operation keys.For details, refer to page 19.Note: Advanced functions consist of the dual count calculating mode, output 1 time (for 2-stage counter), decimal point position, prescale value, displaycolor, output allocation, and key protect level.18Multifunction Preset Counter H7CX-A(Counter Function)Settings for All FunctionsNote: At the time of delivery, the H7CX is set to the 1-stage counter (2-stage counter for H7CX-AW@/-A4W@ models) configuration.
When usingas a 2-stage (or 1-stage) counter, total and preset counter, batch counter, or dual counter, switch to the configuration using the proceduregiven on page 36.Settings that cannot be performed with the DIP switch are performed with the operation keys.Power ON3 s min.See note 2.3 s min.The characters displayed in reverse video are the default settings.When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).If pin 1 of the DIP switch is set to ON, the setting items indicated bywill not be displayed.Set each setting item using therSee note 1.r keys. (rRun modeFor details on operations and display in run mode, refer to page 22.The display depends on the configuration used.Note: 1. If the mode is switched to the function setting mode during operation, operation will continue.2. Changes made to settings in function setting mode are enabled for the first time when themode is changed to run mode.
Also, when settings are changed, the counter is reset(present value initialized and output turned OFF) on returning to run mode.key only for 6-digit models)Note 3:See note 3.When using as a dual counter:Dual countcalculating modeInput modeSee note 4.See note 4.(UP)(DOWN) (UP/DOWN A) (UP/DOWN B) (UP/DOWN C)See note.Note 4: Displayed for output modes other than K-2, D, L, and H only.(Addition) (Subtraction)Note: Displayed only when the outputmode is K-2, D, L, or H.Output modeSee note 5. See note 5.See note 5.See note 5.(N)See note 6.Function setting modeOne-shotoutputtime(F)(C)(R)(K-1)(P)(Q)(A)(K-2)Note: 5.
Display only when the input mode is UP/DOWN A, B,or C with 6-digit models (with H7CX-AU@/-AW@models only for H).(0.01s) (0.50s)(D)(L)When using as a 2-stage counter:Oneshot(0.01s) (0.50s) (99.99s)output2 time Note: Displayed only when theoutput mode is C, R, K-1,P, Q, A, or K-2.(99.99s)Note: Displayed only when the output mode is C, R, K-1, P,Q, A, or K-2.Oneshot(Outputs held) (0.01s) (99.99s)outputIf the output time is 0.00, hold is1 timeCountingspeed(30Hz)(H)Note 6:(5kHz)When using as abatch counter:Reset inputsignalwidth(20ms)DecimalpointpositionOneshotoutput2 time(1ms)(0.01s) (0.50s) (99.99s)Note: Displayed only when the outputmode is C, R, K-1, P, Q, A, or K-2.See note 7.No decimalpointPrescalevaluedisplayed.Note 1: Displayed for output modesother than D, L, and H.Note 2: HOLD cannot be set when theoutput mode is K-2.One digit afterdecimal pointTwo digits afterdecimal pointThree digits afterdecimal pointSee note 7.(0.001)∼(1.000)∼(99.999)Note 7: The displays for 4-digit models are shown insideparentheses.[9.999]NPN/PNPinput mode(NPNinput)(PNPinput)(Red)(Green)Display color(Red-green) (Green-red)Note: Displayed for terminal-block models (except H7CX-A11@) only.OutputallocationNote: Displayed for H7CX-AU@ models only.Key protectlevel(KP-1)(KP-2)(KP-3)(KP-4)Multifunction Preset Counter(KP-5)H7CX-A (Counter Function)19Explanation of FunctionsInput Mode (cntm) (Setting possible using DIP switch.)Prescale Value (pscl)Set increment mode (UP), decrement mode (DOWN), or one of theincrement/decrement modes (UP/DOWN A, UP/DOWN B, or UP/DOWN C) as the input mode.