M070-04 (986759), страница 9
Текст из файла (страница 9)
4.7 kΩ)Hold inputMinimum input signal width: 20 msPulse measurement methodPeriodic measurement (Sampling period: 200 ms)Max. counting speed30 Hz or 10 kHz (selectable)Measuring range30 Hz: 0.001 Hz to 30.00 Hz10 kHz: 0.001 Hz to 10 kHzMeasuring accuracy±0.1% FS ±1 digit max. (at 23 ±5°C)Output modesHI-LO, AREA, HI, LOAuto-zero time0.1 to 999.9 sStartup time0.0 to 99.9 sAverage processingOFF/2/4/8 timesControl outputContact output:3 A at 250 VAC/30 VDC, resistive load (cosφ=1)Minimum applied load: 10 mA at 5 VDC (failure level: P, reference value)Output typeSPDTNEMA B300 Pilot Duty, 1/4 HP 3-A resistive load at 120 VAC, 1/3 HP 3-A resistive load at 240 VACExternal power supply12 VDC (±10%), 100 mA Refer to Safety Precautions (page 60) for details.Key protectionYesPrescaling function0.001 to 99.999Decimal point adjustmentRightmost 3 digitsSensor waiting time250 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)Memory backupEEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.Ambient temperatureOperating: −10 to 55°C (−10 to 50°C if tachometers are mounted side by side) (with no icing or condensation)Storage: −25 to 65°C (with no icing or condensation)Ambient humidity25% to 85%Case colorBlack (N1.5)Note: 1.
Permissible ripple: 20% (p-p) max.2. The display is lit only when the power is ON.44Tachometer H7CX-R■ CharacteristicsItemH7CX-RInsulation resistance100 MΩ min. (at 500 VDC) between current-carrying terminal and exposed non-current-carrying metal parts, and between non-continuous contactsDielectric strength2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-carrying metal parts2,000 VAC (for 100 to 240 VAC), 50/60 Hz for 1 min between power supply and input circuit (1,000 VAC for 24 VAC/12 to 24 VDC)2,000 VAC 50/60 Hz for 1 min between control output, power supply, and input circuit1,000 VAC, 50/60 Hz for 1 min between non-continuous contactsImpulse withstand voltage3 kV (between power terminals) for 100 to 240 VAC, 1 kV for 24 VAC/12 to 24 VDC4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to 240 VAC,1.5 kV for 24 VAC/12 to 24 VDCNoise immunity±1.5 kV (between power terminals)±600 V (between input terminals)Square-wave noise by noise simulator (pulse width: 100 ns/1 µs, 1-ns rise)Static immunityDestruction:Malfunction:15 kV8 kVVibration resistanceDestruction:Malfunction:10 to 55 Hz with 0.75-mm single amplitude, each in three directions four cycles (8 min per cycle)10 to 55 Hz with 0.35-mm single amplitude, each in three directions four cycles (8 min per cycle)Shock resistanceDestruction:Malfunction:294 m/s2 each in three directions98 m/s2 each in three directionsLife expectancyMechanical:Electrical:10,000,000 operations min.100,000 operations min.
(3 A at 250 VAC, resistive load)See Life-test Curve (Reference Values) on page 45.Approved safety standards(See notes 1 and 2.)UL508/Listing, UL 50 Type 4X for indoor use (enclosure rating)CSA C22.2 No. 14, conforms to EN61010-1 (Pollution degree 2/overvoltage category II)EMC(EMI)Emission Enclosure:Emission AC mains:(EMS)Immunity ESD:Immunity RF-interference:Immunity Conducted Disturbance:Immunity Burst:Immunity Surge:Immunity Voltage Dip/Interruption:EN61326EN55011 Group 1 class AEN55011 Group 1 class AEN61326EN61000-4-2:4 kV contact discharge (level 2);8 kV air discharge (level 3)EN61000-4-3:10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);10 V/m (Pulse-modulated, 900 MHz ±5 MHz) (level 3)EN61000-4-6:10 V (0.15 to 80 MHz) (level 3)EN61000-4-4:2 kV power-line (level 3);1 kV I/O signal-line (level 4)EN61000-4-5:1 kV line to lines (power and output lines) (level 2);2 kV line to ground (power and output lines) (level 3)EN61000-4-11:0.5 cycle, 100% (rated voltage)Degree of protectionPanel surface: IP66, NEMA 4 (indoors), and UL Type 4X (indoors) (See note 2.)WeightApprox.
140 gNote: 1. To meet UL listing requirements with the H7CX-R11@ models, an OMRON P2CF-11-@ or P3GA-11 Socket must be mounted on the H7CX. Otherwise,H7CX-R11@ models are considered to meet UL508 recognition requirements.2. The Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter are necessary to ensure IP66, NEMA4, and UL Type 4X waterproofing between theH7CX and installation panel.■ Life-test Curve (Reference Values)Resistive LoadInductive Load1,000No.
of operations (×103)No. of operations (×103)1,00070050030030 VDC (cosφ=1)250 VAC (cosφ=1)70050030030 VDC (L/R=7 ms)1001007070250 VAC cosφ=0.450500123041234Load current (A)Load current (A)Reference: A current of 0.15 A max. can be switched at 125 VDC (cosφ=1) and current of 0.1 A max. can be switched if L/R=7 ms. In both cases,a life of 100,000 operations can be expected. The minimum applicable load is 10 mA at 5 VDC (failure level: P).■ Inrush Current (Reference Values)ModelVoltageApplied voltage Inrush current (peak value)H7CX-R11100 to 240 VAC264 VACH7CX-R11D124 VAC/12 to 24 VDC 26.4 VACTime5.8 A0.7 ms10.4 A1.2 msTachometerH7CX-R45Connections■ Block Diagram(Basicinsulation)Output circuitPower supplycircuit(Basic insulation)(Basic insulation)Display circuitInternal controlcircuitInput circuitKey switchcircuit■ I/O FunctionsInputsOutputsCountReads counting signals.HoldHolds the measurement value and outputs.The hold indicator is lit during hold.OUTOutputs signals according to the specified output mode when a comparison value is reached.Note: Refer to page 55 for details on the hold function.■ Terminal ArrangementHoldCountInternal circuitHold5 6 7Hold40V(−)832Sensor, etc.1 1191012 VDC(+)External power supplyOUT(−)(+)Note: 1.
Terminals 4, 5, and 7 are all for the hold function. The function is the same whichever terminal is connected. Terminals4, 5, and 7 are not connected internally and so do not usethem for bridge wiring.2. Recommended wire: AWG 18 to 24 (Cross-sectional area:0.205 to 0.823 mm2), solid or twisted, copper or aluminum■ Input CircuitsCount and Hold InputsNo-voltage Inputs (NPN Inputs)+14 V1 kΩInternalcircuitINVoltage Inputs (PNP Inputs)Approx. 4.7 kΩIN46InternalcircuitTachometer H7CX-R■ Input ConnectionsThe inputs of the H7CX-R can be used as either no-voltage (short-circuit or open) inputs or voltage inputs. They are set for use as voltage inputsat the time of delivery.No-voltage Inputs (NPN Inputs)Open CollectorVoltage OutputDC Two-wire Sensor4 5 7Operates when the transistor turns ON.34 5 7Terminalnumber6Operates when the transistor turns ON.34 5 7Operates when the contact turns ON.3HoldInputTerminalnumber6Count0VCountInputCountHoldTerminalnumber6InputCountHoldInput30V0V0VHoldPLC orsensorTerminalnumberContact InputSensor4 5 76Operates when the transistor turns ON.No-voltage Input Signal LevelsApplicable Two-wire SensorNo-contact inputLeakage current: 1.5 mA max.Switching capacity: 5 mA min.Residual voltage: 3.0 VDC max.Operating voltage: 10 VDCShort-circuit level (Transistor ON)Residual voltage: 3 V max.Impedance when ON: 1 kΩ max.(The leakage current is 5 to 20 mA when theimpedance is 0 Ω.)Open level (Transistor OFF)Impedance when OFF: 100 kΩ min.Contact inputUse contact which can adequately switch5 mA at 10 V.Note: The DC voltage must be 30 VDC max.Voltage Inputs (PNP Inputs)No-contact Input(NPN Transistor)No-contact Input(PNP Transistor)SensorContact InputSensorTerminal34 5 76numberOperates when the transistor turns ON.CountHoldCountHoldInputCountTerminal34 5 76numberOperates when the transistor turns OFF.Input0V0VHoldInput0VTerminal34 5 76numberOperates when the contact turns ON.Voltage Input Signal LevelsHigh level (Input ON):Low level (Input OFF):Input resistance:4.5 to 30 VDC0 to 2 VDCApprox.
4.7 kΩNote: The DC voltage must be 30 VDC max.TachometerH7CX-R47NomenclatureIndicatorsA Hold Indicator (Orange)Lit when the hold input or hold key isON.B Key Protection Indicator (Orange)Lit when the key protect switch is ON.C Control Output Indicator (Orange)Lit when output is ON.D Comparison Value 1, 2 Stage IndicatorOperation KeysTACHOMETER1HLD25364798G Mode KeyUsed to switch mode and setting items.H Hold KeyUsed to sustain the measurement valueand output.I Up Keys: 1 to 6HLDE Present Value (Main Display)Character height: 9 mm (Red)6th digit1st digitF Comparison Value (Sub-display)Character height: 6 mm (Green)SwitchesJ Key Protect Switch10(Factory setting) OFFON(enable)(disable)11K DIP Switch123ONOFF(Factory setting)48Tachometer H7CX-R45678DimensionsNote: All units are in millimeters unless otherwise indicated.■ Tachometer (without Flush Mounting Adapter)648×48TACHOMETHLDPanel CutoutsPanel cutouts are asshown below.(according to DIN43700).14.472.560 min.ER45+0.6−044.8×44.845+0.6−0HLD60 min.
15 min.■ Dimensions with Flush Mounting Adapter(Adapter and Waterproof Packing Ordered Separately)Y92S-29 (order separately)Waterproof PackingTACHOMETHLDPanelY92F-30 (order separately)Flush Mounting AdapterP3GA-11(order separately)Back ConnectingSocketER(51)58HLD7.548Note: 1. The mounting panel thicknessshould be 1 to 5 mm.2. To allow easier operability, it isrecommended that Adapters aremounted so that the gap betweensides with hooks is at least 15 mm(i.e., so that the panel cutout intervalis at least 60 mm).3. It is possible to mount countersside by side, but only in thedirection without the hooks.If they are mounted side-by-side,water-resistant specificationscannot be ensured.98.7n side by side mounting■ Dimensions with Front Connecting SocketAA = (48n − 2.5)+10P2CF-11(-E) (order separately)Front Connecting SocketWith Y92A-48F1 attached.A = {48n−2.5 + (n−1) x 4}+10H7CX-R11/-R11D1With Y92A-48 attached.A = (51n−5.5)+10109.7112Note: These dimensions vary with the kind of DIN track (reference value).■ Accessories (Order Separately)Note: Refer to page 15 for details.TachometerH7CX-R49Operating Procedures■ Settings for Basic OperationsSettings for basic functions are performed with the DIP switch.(Factory setting)12345678ONOFFItemOFFON1Not used2Counting speed30 Hz3Output modeRefer to the table on the right.10 kHz45Average processingNot used8NPN/PNP input modeNPNPNPEasy Confirmation of Switch Settings Using IndicatorsThe ON/OFF status of the DIP switch pins can beconfirmed using the front display.