NT support tool (V053-E1-1) (986753), страница 23
Текст из файла (страница 23)
Ten times of Undo can be performed.It is invoked by:Menu bar: [Edit] → [Undo]Draw bar: Click on128Common OperationSection 6-1Redoing the operationThe Redo function will repeat the last (most recent) action that was performed. Tentimes of Redo can be performed.It is invoked by:Menu bar: [Edit] → [Redo]Draw bar: Click on6-1-6Aligning ElementsTwo or more elements can be aligned collectively.There are following six functions for alignment. The buttons below are provided onthe alignment bar.S Align Top:(Short cut key: Ctrl + Up Arrow)S Align Bottom:(Short cut key: Ctrl + Down Arrow)S Align Left:(Short cut key: Ctrl + Left Arrow)S Align Right:(Short cut key: Ctrl + Right Arrow)S Centre in a Column:(Short cut key: Ctrl + F9)S Centre in a Row:(Short cut key: Ctrl + Shift + F9)These functions can align the elements to the extremely edge in the selected elements’ range or to the vertical/horizontal center of all the selected objects.[In case of Align Top, Align Bottom, Align Left, Align Right]Align LeftAlignTopAlignBottomAlign Right[In case of Centre in a Column, Centre in a Row]Centrein aRowCentre in a Column129Common OperationSection 6-1However, if touch switch (including elements such as thumbwheel, alarm list/history which contain touch switch within themselves) is included in the selected elements, the touch switch will take precedence for alignment and the other elementswill be aligned to the touch switch as follows.[Example] In case of Align Bottom, Align RightAlignBottomAlignRightBase line for“Align Bottom”Base line for“Align Right”Reference: S Alignment function can be used also in the Edit Object mode.
By using this function in this mode, position of the lamp/touch switch label or image/library forimage/library lamp ON/OFF status can be aligned easily within the element.If alignment function was used in Edit Object mode, only the selected elementwill be moved (Alignment is performed towards the whole area of the element).S Touch switches may not be aligned to the center properly when “Centre in a Column” or “Centre in a Row” is performed because of the defined touch switch gridsize.
(They will be aligned to the nearest center.)S If alignment function is performed when the filter function is activated, the filterfunction will be cancelled.(1) Select multiple elements to be alignedOr: select one element which consists of multiple elements and specify theobjective part after entering the Edit Object mode.(2) Specify any of the aligning method after selecting [Align] from [Edit] menu.Or: right–click the mouse and specify the aligning method after selecting[Align] from pop–up menu. (Short cut key can also be used. Refer to P129)6-1-7Grouping ElementsIt is possible to group multiple elements into one element.When creating a graphic by combining several elements, future editing such ascopying, pasting, and moving will be facilitated if they are grouped.Grouped elements can be returned to individual elements by ungrouping them.In the grouped state, it is not permissible to change the element size and propertysettings.
To change the size or set properties, ungroup the elements.Reference: When saving screen data using mmi format, grid setting information and groupinginformation will not be stored.(Refer to 3-3-3 “Saving the Screen Data (Application) File.” )130Common OperationSection 6-1Grouping(1) Specify the elements to be grouped.(2) Select [Draw] (menu bar), then select [Group].This operation is also possible using the pop-up edit menu; display the pop-upedit menu by right clicking the mouse and select [Group].Ungrouping(1) Select an element in the grouped elements. (Select only one grouped element).(2) Select [Draw] (menu bar), then select [Ungroup].This operation is also possible using the pop-up edit menu; display the pop-upedit menu by right clicking the mouse and select [Ungroup].6-1-8Associating Elements with the Touch SwitchIf the cursor move touch switch has been created independently later than a certain element, this touch switch has to be associated with this element in order tospecify the data input field when the touch switch has been pressed on PT.For NT30, NT30C, NT620S, NT620C, NT625C, it is possible to associate the control code input touch switches (page and line scroll touch switches) with the alarmlist and history.It is also possible to disassociate the touch switch with the elements.Reference: S If the “Auto Arrange” check box is ticked in the Setting property of cursor movetouch switch, the cursor move touch switch will always be moved together withthe attached data input object.
So, it is not possible to move or resize the cursormove touch switch itself independently. To move or resize it, first of all cancel the“Auto Arrange” check box, then move or resize it.S For NT31, NT31C, NT631, NT631C, the touch switch of trend graph and alarmlist/history is built into each element. It is only possible to change the location ofthe touch switch. (Size cannot be changed.)131Common OperationSection 6-1Association(1) Select the touch switch which you want to associate.
(Select only one element.)The touch switches which can be associated to an element should be page orline scroll touch switch.(2) Select [Associate With...] from [Draw] menu.Dialog box which prompts the user to select the elements to be associated willbe displayed.(3) Choose the data input or Alarm which you want to associate. Then click.Disassociation(1) Select the touch switch you want to disassociate. (Select only one element.)(2) Select [Disassociate] from [Draw] menu.Touch switch disassociation will be performed.6-1-9Centralizing the Label of Lamp and Touch SwitchWith the Support Tool, the label of lamp/touch switch can be centralized within theelement (horizontal direction only). This function is useful, for example, when thelabel is edited after the creation of lamp/touch switch. Touch switch has two kindsof areas, one is “displayed figure” and the other is “touch sensing area”.
“CentralizeLabel” is performed toward the touch sensing area.(1) Select the lamp/touch switch you want to centralize.Multiple selection is also possible. However, “Centralize Label” can not beperformed if no lamps or touch switches are included in the selected elements.”Centralize Label” can be performed also when elements other than lamp ortouch switch are included in the selected elements. (Nothing is performed forelements other than lamp or touch switch)(2) Select [Centralize Label] from [Draw] menu, or click on thepress Ctrl key + L)132button.
(orCommon OperationSection 6-1Reference: S Centralization of lamp/touch switch label can be also performed by alignmentfunction (Centre in a Column) in Edit Object mode. However, the result may differsince the alignment function is performed towards the whole lamp/touch switcharea.S If “Centre in a Row” is performed for a label in Edit Object mode, the label iscentralized vertically.6-1-10Setting PropertiesFor each element, properties are set to characterize the individual elements.
Basically, following two types of properties are set.S GeneralGeneral settings such as display color and character size.S Settings (only for elements which have a specific function)Settings related to data conversion, such as PC (PLC) address and memorytable address.In addition to the properties shown above, some elements have the following properties.S Light Function (only for lamps and touch switches)Setting of bits (lamp bits) for control which are used when changing display.S Logging (Data Logging property) (only for trend graph)Setting of the data logging function which records data.The following explains only the basic settings.
For details of the properties of eachelement, refer to 6-2 “Fixed Display” and later sections.Displaying the Property Setting Dialog BoxThe property setting dialog box is displayed in any of the following operations.S Using the mouse (1)(1) Double click an element.S Using the mouse (2)(1) Right click the mouse on an element, then select [Properties...].S Using the menu(1) Specify the element for which you want to display properties (specify onlyone element).(2) Select [Draw] (menu bar), then select [Properties].S Using the keyboard(1) Specify the element for which you want to display properties (specify onlyone element).(2) Press the Enter key while holding down the Alt key.133Common OperationSection 6-1Setting the line typeYou can select the type of line for polylines, broken-line graphs, and trend graphs.SolidDashDot-dashDot-dot-dashThe line type is set in a property of individual elements.Setting the display colorSet the display color of elements.Color setting is possible with NT30C, NT31C, NT620C, NT625C, and NT631C.The colors which can be used are shown below.White, black, blue, red, magenta, green, cyan, yellowFor some elements, [Transparent] may be specified to display a transparent background.