H136-E1-01A E5_N Datasheet (986779), страница 8
Текст из файла (страница 8)
3 dia.Lead40 × 4018• PlugTwo, M3 (depth: 4)Approx. 6 dia.1530(22)Digital Temperature ControllersE5AN37Operation■ Outline of Operation ProceduresThe following diagram illustrates the entire setting level. A password is required to enter the advance function setting level and the calibration level.Some parameters may not be displayed depending on the protection settings and operation conditions.The control operation will stop when switching from operation level to initial setting level.]Power ONStarting in manual modeStarting in automatic modePress the LevelKey for at least 1 s.Operation LevelCPress theLevel Keyless than 1 s.a-mPress the Level Keyfor at least 1 s;display will flash.Press the Level Key(Seefor at least 3 s whilenote 3.) a-m is displayed.ManualModeManualControl LevelPress theLevel Key forat least 1 s.Press theLevel + Mode Keys;display will flash.Adjustment LevelC(Seenote 1.)Press theLevel + ModeKeys.Press the Level Key for at least 1 s2510025100for at least 1 s;display will flash.Press the Level +Mode Keys for at least3 s.
(See note 4.)Press the Level Key forat least 3 s.Control stops.CommunicationsSetting LevelInitial Setting LevelCProtect LevelPress the Level Keyfor less than 1 s.Input password.Press the LevelKey for at least 1 s.Set value −169Advanced FunctionSetting LevelControl in progressInput password.Set value 1201Calibration LevelNote: 1.2.3.4.(Seenote 2.)Control stoppedNot displayed for some modelsLevel changeOperation level entered for software reset.You cannot move to other levels by operating the keys on the front panel from the calibration level.
You must turn OFF the power supply.You can move only to the operation level by operating the keys on the front panel from the manual control level.The time taken to move to the protect level can be adjusted by changing the “Move to protect level time” setting.TroubleshootingIf an error occurs, an error message will be displayed on the No.
1 display. Use the error message to check the type of error and correct the erroraccordingly.No. 1 displayErrorCorrectionOutput status at errorControl outputs Alarm outputss.err (S. Err)Input error(See note 2.)Check for input wiring errors, broken wires, short-circuits, and input type error.OFFA/D convertererror(See note 2.)Check for an input error and then cycle the power supply.
If the same error is stillOFFdisplayed, repairs will be necessary.If the Temperature Controller is normal after cycling the power supply, the error may havebeen caused by noise. Check for noise being generated nearby.e111 (E111)Memory errorh.err (H. Err)Internal circuiterror(See note 2.)Cycle the power supply. If the same error is still displayed, repairs will be necessary.OFFIf the Temperature Controller is normal after cycling the power supply, the error may haveOFFbeen caused by noise. Check for noise being generated nearby.Handled asabnormally hightemperatureOFFOFFOFFNote: 1. If the input exceeds is within the controllable range but exceeds the display range (−1999 to 9999),will be displayed if the temperature is less than−1999 andwill be displayed if the temperature is more than 9999.
The control and alarm outputs will function normally during these displays. Referto the E5CN/E5CN-U/E5AN/E5EN Temperature Controller User's Manual (Cat. No. H134) for information on the controllable range.2. These errors are displayed only when the PV/SP is displayed. Errors are not displayed in other display modes.38Digital Temperature Controllers E5@NDigital Temperature ControllersE5@N39■ ParametersSome parameters are not displayed depending on themodel of the Controller and parameter settings. For details,refer to the E5CN/E5AN/E5EN/ Temperature ControllerUser's Manual (Cat.
No. H134).Press the Level Key for at least 3 s.(Display flashes for at least 1 s.)Displays other than that for switchingbetween automatic and manualPower ONStarting in manual modeManual Control LevelC25 PID control onlyPress theLevel Keyfor atleast 1 s.PV/MVStarting in automaticmodePress the Level Key less than 1 s.Adjustment LevelOperation Levell.adjaAdjustment leveldisplayd Derivative time40offaac-sc Cooling coefficientct1 Heater current value 10.0 monitor1.00aCaaCahb1 Heater burnout 10.0 detection50.0wt-b Wait band0.0aasp-1 SP 10CSP used by multi-SPasp-2 SP 2sprt SP ramp set valuear-s0.0aRun/stoprunaPress the Level + ModeKeys for at least 3 s.Display flashes.The time taken to move to the protect level canbe adjusted by changing the "Move to protectlevel time" setting.CommunicationsSetting LevelDisplayed only for models with communications.Changes are effective after cycling power or aftera software reset.asp-3 SP 3ol-l MV lower limit0-5.0ashiftins Temperature input1-point shifta0.0insh Upper-limittemperature input0.0Set either of these parameters.2-point shiftapmoVinsl Lower-limit0.0 temperature inputaMove to protect levelDisplayed only when a password0 is set.
Restricts moving to protectlevel.aoaptaOperation/adjustmentprotectionRestricts displaying and modifying0 menus in operation, adjustment,and manual control levels.aInitial Setting/Communications Protectionicpt This protect level restricts movement1 to the initial setting, communicationssetting, and advanced functionsetting levels.achange protectionwtpt SettingProtects changes to setups byoffoperating the front panel keys.aon parameter mask is set.aprlp0aDigital Temperature Controllers E5@NpselProtocol settingSwitches betweencwf CompoWay/Fa(SYSWAY) and Modbus.u-no Communications1aUnit No.CompoWay/Fbps Baud rate (SYSWAY) only9.6alen Data bits7asbit Stop bits2mask enablepmsk ParameterDisplayed only when a40Press the Level Keyless than 1 s.Press the Level + ModeKeys for at least 1 s.Protect Levela105.0c-o MV monitor (cooling)aoffol-h MV upper limit0aC0.0amV-e MV at PV error0o MV monitor (heating)rsetasp-0 SP 0000.0aal3l Lower-limitalarm value 3aProgram startsoaksktr Remainingtime monitormV-s MV at stop50.0C0.0ahs2 SSR failure detection 20Caoffaal3h Upper-limitalarm value 3acurrentlcr2 Leakagevalue 2 monitorprstal-3 Alarm value 30CaaC0acurrentlcr1 Leakage0.0 value 1 monitor1al2l Lower-limitalarm value 2aCasoak Soak timea0current value 2ct2 Heater0.0 monitorchys Hysteresis (cooling)al2h Upper-limitalarm value 2a0.0ahb2 Heater burnout 20.0 detectionhs1 SSR failure detection 1current value 1ct1 HeatermonitorCa1.0a0aHysteresis settingsal-2 Alarm value 2aC0hys Hysteresis (heating)aC0aCSP ramp monitorsp-mManual reset value1.0aaCalcr2 Leakage current value0.0 2 monitoral1l Lower-limitalarm value 10setm-sp Multi-SP0 point setting50.0 of P or PD control.aCswitching function is added.aof-r Clear the offset during stabilization0.0 1 monitorCc-db Dead bandPress theLevelKey for atleast 3 s.(Displayflashesfor atleast 1 s.)0.0lcr1 Leakage current valueCHeating/coolingact2 Heater current value 20.0 monitoral1h Upper-limitalarm value 1Auto/manual switchcontrol onlya-m PIDAdded when auto/manualacmwt Communications writingCa233a0C0PID settingsal-1 Alarm value 1avalue/25 Processset pointCi Integral timeCdisplay is added.aaoffCp Proportional band8.0at AT execute/cancelCvalue25 ProcessAdded when PVCCDisplayed only once whenentering adjustment level.Set either of these parameters.
Set either of these parameters. Set either of these parameters.Press the Level Key less than 1 s.Password to move toprotect levelPassword settingaprty CommunicationseVenparityasdwt Send delay20aPress the Level Key for at least 1 s.Initial Setting LevelAdvanced Function Setting LevelPress the Level Key less than 1 s.in-t Input typeParametera100c1300arestaConptrn Programoff patterncp Control period (heating)20aa2hbh2Linear outputtr-h Transfer output upper limit100.0tr-lTransfer output lower limitaa2of Alarm 2 OFF delayst-b ST stable range015.0aaalfa αa3of Alarm 3 OFF delay0aaaalm3 (E5AN/E5EN only)acsel Display text switchonat-u Soak time unitmaalsp Alarm SP selectionsp-macmoV Move to calibration0 levelaistp Input shift typeins10.0o1-t Linear current output4-20ainf Input digital filter0.0000.65aa3on Alarm 3 ON delaya1of Alarm 1 OFF delayHeater burnoutaCaalm3 Alarm 3 assignmenta0.1 hysteresistr-t Transfer output typea0aaalm2 assignment0aoffAlarm 3 typeaalm2 Alarm output 2a1on Alarm 1 ON delaya2on Alarm 2 ON delayhbl Heater burnout latchaalm1 assignmentaaalt2 Alarm 2 typeoffalh3 Alarm 3 hysteresison detection2aalm1 Alarm output 1pV-b PV stable range5.0hbu Heater burnoutanone assignmentaaalt1 Alarm 1 typealt3C0.2or-rout2 Control output 2redan-o alarmCo assignmentacolr PV display coloralh2 Alarm 2 hysteresisaoreV Direct/reverse operationaout1 Control output 1aal3n Alarm 3 open in203.0 widthoff switchingaalbab LBA detectionrlrV MB command logic0.2c-cp Control period (cooling)Con compensating methodn-o alarmSet the pulse output cycle.8.0 thresholdaal2n Alarm 2 open inClbal LBA detectionacjc Cold junctionalh1 Alarm 1 hysteresisaaCa0.2When assigning PIDor control output topulse outputInput error outputoffaaaseroaFor input type oftemperature,standard, or PID0an-o alarmstndlba LBA detection time3al1n Alarm 1 open ins-hc Standard or heating/ coolingaprlt Move to protect level timeStandby sequenceaast STaa reset methodonof0.1 hysteresisoffmaahsh SSR failurea3lt Alarm 3 latchacntl PID ON/OFFoffaspru SP ramp time unit-200hsl SSR failure latchoffasl-l SP lower limitaa2lt Alarm 2 latchoffLimit the set point.on detectionamspu Multi-SP usesahsu SSR failureoffasl-h SP upper limitaa1lt Alarm 1 latchstop assignment 2temperatureoffaeV-2 Event inputunitd-u TemperatureFor input type of°C, °FaAuto/manualswitching functionadditionrt RToff display modeaaCanone assignment 1For input type of analog0offret Automatic return ofeV-1 Event inputdp Decimal pointamadoffa0aao-dp MV display1 Four SPs: 2in-l Scaling lower limitoff stop/erroraNumber of multi-SPuseseV-m Two SPs: 1amVse Additional MV foroff displayoffin-h Scaling upper limitCpVad Additional PVinit initialization5aaLinear outputaamoV0aMove to advancedfunction setting levelMove by setting password (−169).Displayed when initial setting/communications protection is set to 0Digital Temperature ControllersE5@N41Improvements to E5@N Functionality■ ChangesModel numbers have been changed to allow for multi-inputspecifications.Before ChangeE5@N-@@@TC (models for thermocouples)E5@N-@@@P (models for platinum resistance thermometers)After ChangeE5@N-@@@T(Models that support both thermocouples and platinum resistancethermometers)Precautions in Replacing PreviousControllers• The input type setting numbers have changed to allow for multiinput specifications.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
