H134-E1-01A E5_N UsersManual (986777), страница 28
Текст из файла (страница 28)
Whenthe ST function is in operation, be sure to turn ON the power supply of theload connected to the control output simultaneously with or before startingController operation.• Auto-tuning can be started during self-tuning.ParameterSTSetting150Setting rangeoff: ST function OFF, on: STfunction ONUnitNoneDefaultonSection 5-6Initial Setting Level■ Related ParametersSeeptrnInput type: Page 146, PID ON/OFF: Page 149 (initial setting level), ST stablerange (advance function setting level): Page 165Program PatternThis parameter sets the type of control when using the simple program function.• If the program pattern is set to OFF, the simple program will not operate.FunctionSetting• If the program pattern is set to STOP, the RUN/STOP status will change toSTOP after the soak time has expired.
If the program pattern is set toCONT, control will continue in RUN status after the soak time has expired.offSetting rangeSimple program function turned OFFDefaultoffstopcontGo to STOP mode at end of program.Continue in RUN mode at end of program.■ Related ParametersSeeProgram start, Soak time remain: Page 123, RUN/STOP: Page 124 (operationlevel)Soak time, Wait band (adjustment level): Page 141Soak time unit (advanced function setting level): Page 181cpControl Period (Heat)c-cpControl Period (Cool)The cooling control output and heating control output must be assignedto relay/voltage outputs.The control must be set to 2-PIDcontrol.For the “control period (cool)” parameter, the control must be set to heating/cooling control.• These parameters set the output periods.
Set the control periods takingthe control characteristics and the electrical durability of the relay intoconsideration.Function• For standard control, use the “control period (heat)” parameter. The “control period (cool)” parameter cannot be used.• Whenever the heating control output is a current output, the “controlperiod (heat)” parameter cannot be used.• For heating/cooling control, the control period can be set independentlyfor heating and cooling. The “control period (heat)” parameter is used forthe heating control output, and the “control period (cool)” parameter isused for the cooling control output.ParametersSettingSeeControl period (heat)Control period (cool)Setting range0.5 or 1 to 990.5 or 1 to 99UnitSecondSecondDefault2020■ Related ParametersPID ON/OFF (initial setting level): Page 149151Section 5-6Initial Setting LevelorevDirect/Reverse Operation• “Direct operation” refers to control where the manipulated variable isincreased when the process value increases.
Alternatively, “reverse operation” refers to control where the manipulated variable is increased whenthe process value decreases.FunctionSetting rangeDefaultor-r: Reverse operation, or-d: Direct operationor-rSettingalt1Alarm 1 TypeAlarm 1 must be assigned.• Select one of the following three alarm 1 types:Deviation, Deviation range, or Absolute valueFunctionSet valuesAlarm typeAlarm output operationWhen alarm value X When alarm value Xis positiveis negativeSetting0Alarm function OFF1 (See note Upper- and lower-limit1.)23Upper-limitLower-limitOutput OFFL HONOFFXONOFFSPXONOFF4 (See note Upper- and lower-limit1.)rangeONOFF5 (See note Upper- and lower-limit1.)with standby sequenceONOFFSee note 2.SPSPL HONOFFONOFFXSPXSPSee note 3.SPL HSee note 4.SPSee note 5.6789152Upper-limit with standbysequenceONOFFLower-limit with standbysequenceONOFFAbsolute-value upperlimitONOFFAbsolute-value lower-limitONOFFXSPXSPX0X0ONOFFONOFFONOFFONOFFXSPXSPX0X0Section 5-6Initial Setting LevelSet valuesAlarm type101112NoteAlarm output operationWhen alarm value X When alarm value Xis positiveis negativeAbsolute-value upperlimit with standbysequenceAbsolute-value lower-limitwith standby sequenceONOFFLBA (alarm 1 type only)---XONOFFXONOFF0XONOFF00X0(1) With set values 1, 4 and 5, the upper- and lower- limit values can be setindependently for each alarm type, and are expressed as “L” and “H.”(2) Set value: 1 (Upper- and lower-limit alarm)Case 1Case 2Case 3 (Always ON)H < 0, L < 0LHSP L HH SPH < 0, L > 0|H| < |L|H > 0, L < 0|H| > |L|SPLH < 0, L > 0|H| ≥ |L|L SPHSP HLH > 0, L < 0|H| ≤ |L|(3) Set value: 4 (Lower limit range)Case 1Case 2Case 3 (Always OFF)H < 0, L < 0LH SPH < 0, L > 0|H| < |L|SP LHHH > 0, L < 0|H| > |L|HSPLL SPSP H LH < 0, L > 0|H| ≥ |L|H > 0, L < 0|H| ≤ |L|(4) Set value: 5 (Upper- and lower-limit with standby sequence)• For the lower-limit alarms in cases 1 and 2 above, the alarm is normally OFF if upper- and lower-limit hysteresis overlaps.• In case 3, the alarm is always OFF.(5) Set value: 5 (The alarm is always OFF if upper- and lower-limit alarm hysteresis with standby sequence overlaps.)• Set the alarm type independently for each alarm in the “alarm 1 to 3 type”parameters in the initial setting level.
The default is 2 (Upper-limit alarm).■ Related ParametersSeeAlarm value 1: Page 124, Alarm value upper limit 1, Alarm value lower limit 1:Page 126 (operation level)Standby sequence reset: Page 161, Alarm 1 open in alarm: Page 162, Alarm1 hysteresis: Page 163, Alarm 1 latch: Page 167 (advanced function settinglevel)153Section 5-6Initial Setting Levelalt2Alarm 2 TypeAlarm 2 must be assigned.• Select one of the following three alarm 2 types:Deviation, Deviation range, or Absolute valueFunctionRefer to the alarm 1 type list.Setting■ Related ParametersSeeAlarm value 2: Page 125, Alarm value upper limit 2, Alarm value lower limit 2:Page 126 (operation level)Standby sequence reset: Page 161, Alarm 2 open in alarm: Page 162, Alarm2 hysteresis: Page 163, Alarm 2 latch: Page 167 (advanced function settinglevel)alt3Alarm 3 TypeAlarm 3 must be assigned.• Select one of the following three alarm 3 types:Deviation, Deviation range, or Absolute valueFunctionRefer to the alarm 1 type list.Setting■ Related ParametersSeeAlarm value 3: Page 125, Alarm value upper limit 3, Alarm value lower limit 3:Page 127 (operation level)Standby sequence reset: Page 161, Alarm 3 open in alarm: Page 162, Alarm3 hysteresis: Page 163, Alarm 3 latch: Page 167 (advanced function settinglevel)154Section 5-6Initial Setting Leveltr-tTransfer Output TypeA current output must be assigned.• When current output is to be used as transfer output, this parameter setsthe transfer output type.• If current output is not to be used as transfer output, set this parameter toOFF.FunctionTransfer output typeSettingOFFSet pointoffspSet point during SP rampPVsp-mpvMV monitor (heating)MV monitor (cooling)mvc-mvDefaultoff■ Related ParameterSeeTransfer output upper limit, Transfer output lower limit (initial setting level):Page 155tr-htr-lTransfer Output Upper LimitTransfer Output Lower LimitA current output must be assigned.The transfer output type must not beset to OFF.• This parameter sets the upper and lower limit values of transfer outputs.FunctionTransfer outputtypeSetting rangeDefaultTransferoutput lowerlimitSettingTransferoutput upperlimitSet pointSP lower limit to SP upper limitSet point during SP lower limit to SP upper limitSP rampSP lower limitSP upper limitPVTemperature Senor setting range lower limitto sensor setting range upperlimitAnalogAnalog scaling lower limit toanalog scaling upper limitSensor settingrange lowerlimitScaling lowerlimitSensor settingrange upperlimitScaling upperlimitMV monitor(heating)StandardHeating/cooling0.0 to 105.00.0100.0MV monitor(cooling)−5.0 to 105.00.0 to 105.0UnitEU%■ Related ParameterSeeTransfer output type (initial setting level): Page 155155Section 5-6Initial Setting Levelo1-tLinear Current OutputA current output must be assigned.This parameter selects the output type for linear current outputs.• Select either 4 to 20 mA or 0 to 20 mA.FunctionTransfer type4-20: 4 to 20 mA0-20: 0 to 20 mADefault4-20Setting■ Related ParameterSeeamovTransfer output type (initial setting level): Page 155Move to Advanced Function Setting LevelThe “initial setting/communicationsprotect” parameter must be set to 0.• Set the “move to advanced setting level” parameter set value to “−169.”Function• Move to the advanced setting level either by pressing the M key or O keyor by waiting for two seconds to elapse.■ Related ParameterSee156Initial setting/communications protect (protect level): Page 116Section 5-7Advanced Function Setting Level5-7Advanced Function Setting LevelThe advanced function setting level is used for optimizing Controller performance.
To move to this level, input the password (“−169”) from the initial setting level.To be able to enter the password, the “initial setting/communications protect”parameter in the protect level must be set to 0.• The parameters in this level can be used when the “initial setting/communications protect” parameter is set to 0.• To switch between setting levels, press the O key.• To change set values, press the U and D keys.Power ONAdjustmentLevelOperationLevelPress theO Key less than 1 s.Press the O Keyfor at least 1 s.Press theO Keyfor atleast 3 s.C25100Press the O Key for atleast 3 s.Control stops.Initial SettingLevelCommunicationsSettingLevelPress theO Key for less than 1 s.Press the O Keyfor at least 1 s.Password inputset value −169Advanced FunctionSetting LevelControl in progressControl stopped157Section 5-7Advanced Function Setting LevelAdvanced Function Setting LevelPagehbl Heater burnout164rlrv MB command169hsl HS alarm175ev-m Number of159hbh Heater burnout164colr PV display169hsh HS alarm175ev-1 Event input160pv-b PV stable band170lba LBA detection176ev-2 Event input160a1on Alarm 1 ON171none assignment 1Mstop assignment 2off latchM0.1 hysteresisMCst-b ST stable165alfa α16515.0 rangeM166161pvad Additional PVrest Standbysequence161o-dp MV displayal1n Alarm 1 open162alh1 Alarm 1163al2n Alarm 2 open162alh2 Alarm 2163al3n Alarm 3 open162alh3 Alarm 3163160spru SP ramp timeoffMm unitMaresetMn-o in alarmM0.2 hysteresisM0.2 hysteresisMn-o in alarmM0.2 hysteresisMhbu HB ON/OFFonMinit0 timeM0 delayClbal LBA level176lbab LBA band1778.0M171166a3on Alarm 3 ON171out1 Control output 1177166a1of Alarm 1 OFF172out2 Control output 2178ret Display auto-167a2of Alarm 2 OFF172alm1 Alarm 1178a1lt Alarm 1 latch167a3of Alarm 3 OFF172alm2 Alarm 2179a2lt Alarm 2 latch167istp Input shift type172alm3 Alarm 3180a3lt Alarm 3 latch167at stop andmvse MVerror addition173csel Character180amad Auto/manualselect addition1730.0 filterMoff displayMoffMoff return timeMoffM3 level timeMoff outputMjunctioncjc ColdcompensationonmethodM0 delayM0 delayM0 delayM0 delayM168168rt RThsu HS alarm useonMo assignmentMnone assignmentMalm1 assignmentMalm2 assignmentMalm3 assignmentMon selectMt-u Soak time unitmMoffMoffMC3.0MoffMprlt Move to protect 168sero Input error0 delayMins1MoffM163C0.1 hysteresisMa2on Alarm 2 ONoffMn-o in alarmMred colorMoff latchMMinf Input digitalmspu Multi-SP usesoff logic switchingM5.0M0.65MMCPage1581 multi-SP usesMCPageinit Parameteroff initializationMCPage181174alsp Alarm SP181174cmoV Move to181sp-m selectionM0 calibration levelMParameter Initialization• This parameter returns all parameter settings to their defaults.• After the initialization, the set value automatically turns off.FunctionSetting rangeoff: Initialization is not executed.fact: Initializes to the factory settings described in the manual.Setting158DefaultoffSection 5-7Advanced Function Setting Levelev-mNumber of Multi-SP UsesEvent inputs must be supported.Multi-SP is a function for setting set points 0 to 3 in advance, and switchingbetween these set points using the ON/OFF combinations of event inputs 1and 2.FunctionThe “number of multi-SP uses” parameter is used when the number of presetset points is either two or four.This parameter determines whether the “event input assignment 1” and “eventinput assignment 2” parameters are displayed.The “number of multi-SP uses” parameter displays which functions areassigned to event inputs 1 and 2.SettingNumber of 0 (Seemulti-SPnoteuses1.)12NoteSettingsEvent inputsEvent inputEvent inputFunction ofFunction ofassignment 1 assignment 2 event input 1 event input 2NONE, STOP, MANU, PRSTNone, or switching RUN/(See note 2.)STOP, auto/manual, or program starts(Not disNONE, STOP, Multi-SP, 2None, orplayed.)MANU, PRST points (switch- switching(See note 2.) ing set points RUN/STOP,0 and 1)auto/manual,or programstarts(Not displayed.)Multi-SP, 4 points (switchingset points 0, 1, 2, 3)(1) If the “number of multi-SP uses” parameter is set to 0, both input assignments 1 and 2 can be set.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
