ZEN-SOFT01-V3 ZEN Support Software_Operation Manual (986766), страница 7
Текст из файла (страница 7)
The Status Bar display will change fromRUN to STOP.Monitoring Programs3-7-1MonitorThis section describes how to monitor programs being executed bythe ZEN.The ZEN must be connected and online and the project file openedbefore the programs can be monitored.
The ZEN and ZEN SupportSoftware programs must be the same before programs can be monitored. Use the procedures outlined under 3-3 Transferring Programsto the ZEN, 3-4 Transferring Programs from the ZEN, and 3-5 Verifying Programs with ZEN to transfer and verify the programs.1,2,3...461.Use the procedure outlined under 3-6 Operating and Stopping theZEN to start ZEN operation. Check that the Status Bar displaychanges from STOP to RUN.2.Click the Toggle Monitoring Button on the Toolbar or select ZEN/Monitor from the Menu Bar.Section 3-7Monitoring Programs3.3-7-2When the mode is changed to MONITOR, the closed circuits ofthe ZEN ladder program are highlighted in green.Displaying Present ValuesPresent values, the ON/OFF status of inputs, etc., can be displayedduring monitoring of programs being executed by ZEN.During monitoring, moving the cursor to a timer/counter or other output will cause the present value to be displayed.Present value display3-7-3Changing Settings OnlineSet values can be changed while connected to ZEN online.1,2,3...1.While online, use either the mouse or the cursor keys to highlightthe output that is to be changed.
Then use any of the followingmethods to change the setting.• Press the Enter Key or double-click.• Select Edit(E)/Edit(E) from the Menu Bar.47Section 3-8Setting and Resetting Inputs• Click the right mouse button and select Edit(E).2.The Edit Dialog Box will be displayed. When the settings arechanged and the dialog box closed, the changes will be transferred to ZEN and reflected there.Note The following table shows the settings that can be changedonline.Bit type3-8Content of changeTimer (T)Time settingHolding timer (#)Time settingCounter (C)Counter settingWeekly timer (@)Start/stop days of the week, timesCalendar timer (*)Start/stop months, daysAnalog comparator (A)Input bits, constants, operatorsSetting and Resetting InputsThis section describes how to set (turn ON) and reset (turn OFF)ZEN bits from the ZEN Support Software.48Section 3-9Clearing ErrorsThe ZEN must be connected and online and the project file openedbefore inputs can be set or reset.
Also, the ZEN and ZEN SupportSoftware programs must be the same before inputs can be set orreset. Use the procedures outlined under 3-3 Transferring Programsto the ZEN, 3-4 Transferring Programs from the ZEN, and 3-5 Verifying Programs with ZEN to transfer and verify the programs.!Caution Check that connected devices are safe before changing bit status. Injuries may occur if bit status is changed carelessly.1,2,3...1.Use the procedure outlined under 3-6 Operating and Stopping theZEN to start ZEN operation. Check that the Status Bar displaychanges from STOP to RUN.2.Use the procedure outlined under 3-7 Monitoring Programs tochange to MONITOR mode.3.Use the mouse or cursor keys to move to the input that is to beset or reset, and then perform either of the following operations:• Select ZEN(Z)/Set/Reset Operation and then either Set Operation(W) or Reset Operation(F) from the Menu Bar.• Click the right mouse button and then select Set/Reset Operation(S) and then either Set Operation(W) or Reset Operation(F).Note The inputs that can be set or reset are shown in the followingtable.Bit typeCommentsCPU Unit input bits (I)Input terminal ON/OFF status has priority.CPU Unit output bits (Q)Set/reset possible for inputs only.
(Not possible for outputs.)Expansion I/O Unit inputbits (X)Input terminal ON/OFF status has priority.Expansion I/O Unit outputbits (Y)Set/reset possible for inputs only. (Not possible for outputs.)Work bits (M)Work bits (H)3-9Clearing ErrorsIf an error occurs, use the following procedure to clear the error andthen remove the cause of the error.The ZEN must be connected and online for this operation.1,2,3...1.Select ZEN/Error Clear from the Menu Bar to clear the error.49Section 3-9Clearing Errors2.NoteRepeat this step to clear multiple errors.a)Refer to Section 6 Troubleshooting in the ZEN OperationManual (W385) for information on ZEN errors.b)ZEN errors that occur while online will be displayed in theStatus Bar.Error display50SECTION 4System SettingsThis section describes ZEN system settings, how to set passwords to protect ZEN ladder programs,and how to clear the ZEN memory.4-1ZEN Settings .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524-1-1Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524-24-3Setting a Password . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Protecting Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554-3-1Setting Program Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554-1-24-3-24-4Time Settings . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Removing Program Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Clearing ZEN Memory . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 5651Section 4-1ZEN Settings4-1ZEN SettingsThis section describes how to change ZEN settings from the ZENSupport Software.4-1-1Settings1,2,3...1.Select ZEN/Set Protection/Settings from the Menu Bar.2.The Settings Dialog Box will be displayed. Make the settings foreach item.SettingDetailsDefaultDaylight saving time(See note a.)None, manually, EU Type,US TypeNoneDisplay languageEnglish, Japanese, German,French, Italian, SpanishEnglishContrast control(See note b.)Light, Slightly light, Medium,Slightly shaded, ShadedMediumBacklight control(See note b.)2 min, 10 min, 30 min,always2 minInputfilterOFF: No input filterOFFCPU UnitExpansion I/O Unit 1 ON: With input filter(See note c.)Expansion I/O Unit 2(See note c.)Expansion I/O Unit 3(See note c.)52Node No.Specify a node numberbetween 0 and 9.0Send delay time(See note d.)This is the delay time forsending the initializationcommand to the modem seton the ZEN side.0Modem initialization command (See note d.)Initialization of the modemconnected to the ZEN.NoneSection 4-1ZEN SettingsNote a) Daylight saving can be used for CPU Units that havebuilt-in calendar and clock functions (ZEN-@@C1@@@(-V1)).b) Contrast and backlight control can be used for LCD-typeCPU Units (ZEN-@@C1@@-@(-V1)).c) Input filters can be set for Expansion I/O Units onlywhen Expansion I/O Units are connected.d) Do not make any setting for send delay time or modeminitialization command.
These options are for futurefunction expansion.4-1-23.Click the OK Button to save the settings.Click the Cancel Button to discard the settings.Click the Initialization Button to return to the default settings.4.Settings can be sent between the ZEN and the ZEN Support Software if the ZEN is connected and online.Click the Transfer to ZEN Button to transfer the settings to theZEN or the Transfer from ZEN Button to transfer the settingsfrom the ZEN to the ZEN Support Software.Press the Compare with ZEN Button to compare the settings onthe computer and the ZEN.Time SettingsUse the following procedure for ZEN-@@C1@@-@(-V1), which havetime functions, to set the date and time.The ZEN must be connected and online to set the date and time.1,2,3...1.Select ZEN/Set Protection/Time Setting from the Menu Bar.2.The Time Settings Dialog Box will be displayed.
Set the date andtime for the internal ZEN clock.SettingsDetailsZEN inter- Datenal clockEdit the ZEN date. (Date read from ZEN at startup or same date as computer)TimeEdit the ZEN time. (Time read from ZEN at startup or same time as computer)53Section 4-2Setting a PasswordSettingsPC time3.DetailsDateDisplays the computer date.TimeDisplays the computer time.Click the OK Button to send the settings to the ZEN.Click the Cancel Button to discard the settings.Click the Synchronization Button to use the computer date andtime as the ZEN date and time.
When the Synchronization Buttonis clicked, the computer date and time will be shown under theZEN date and time on the screen, but these settings will not besent to the ZEN.Note To set the date and time display styles, select Settings/ControlPanel/Regional Settings from the Start menu.
Select Date toset a date style or Time to set a time style.4-2Setting a PasswordThis section describes how to set a password for the ZEN SupportSoftware. This password is used to set and clear protection for ZENprograms.Note Refer to 4-3 Protecting Programs for information on how to setand clear ZEN program protection.1,2,3...541.Select ZEN/Set Protection/Set Password from the Menu Bar.2.The Set Password Dialog Box will be displayed. Enter the password and confirm the password.3.Click the OK Button to set the password as entered. Click theCancel Button to clear the entered password.
Click the DeletePassword Button to delete an existing password.Section 4-3Protecting Programs4-3Protecting ProgramsThis section describes how to protect ZEN programs from intentionalor unintentional alteration by other users. Protected ZEN programscannot be altered until the protection is removed and the protectioncan only be removed if the password is input correctly.
For these reasons, care must be taken when using program protection.The ZEN must be connected and online before program protectioncan be executed.Note Refer to 4-2 Setting a Password for information on how to set andchange passwords.4-3-1Setting Program Protection1,2,3...1.Click the Set Protection Button on the Toolbar or select ZEN/Protect/Set from the Menu Bar. The Set Protection Dialog Boxwill be displayed.2.Enter the 4-digit password set under the password settings.Once the above procedure has been completed, programs cannot be transferred to or from the ZEN or compared with the ZENuntil the protection is removed.4-3-2Removing Program Protection1,2,3...1.Click the Release Protection Button on the Toolbar or selectZEN/Protect/Release from the Menu Bar.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
