NT21_Setup Manual (V068-E1-1) (986757), страница 13
Текст из файла (страница 13)
For the host (a personal computer, an FA computer, etc.), its settingshould be compatible to one of the communication conditions listed in the following table. Set the same communication conditions at the NT21 by the memoryswitch. (page 132).ItemSettings at the hostInput/Output portRS-232CBaud rate1,200, 2,400, 4,800, 9,600, 19,200, or 38,400 bps.Data bits7 bits, 8 bitsStop bits1 bits, 2 bitsParityNone, even, oddFlow controlNone, RS/CS, XON/XOFF4-1-2 Connecting Directly between RS-232C PortsThe method for connection between the RS-232C ports of the NT21 and the hostis described here.Recommended Connector CableWhen making the connector cable, as far as possible use the recommendedconnectors, connector hoods, and cables indicated in the table below. SomeUnits come supplied with one connector and one connector hood.Check the required components and prepare them in advance.NameModelRemarksDelivered withCS-series CS1G/CS1H,CS1G-H/CS1H-HCJ-series CJ1GXM2A-0901Connector9-pinMade by OMRONC-series CQM1,C200HS,C200HX/HG/HE(-Z)E,CVM1/CV-series CPUUnitsCV500-LK201XM24-250125-pinMade by OMRONCV500-LK201C200H-LK201-EV163SectionConnecting to the RS-232C Port at the HostNameModelRemarks4-1Delivered withC-series CQM1,C200HS,C200HX/HG/HE-(Z)E,9-pinMade by OMRONXM2S-0911CVM1/CV-series CPUUnitsCV500-LK201ConnectorXM2S-0913hoodCable9-pinMade by OMRON---XM2S-0911-E9-pinMade by OMRONCS-series CS1G/CS1H,CS1G-H/CS1H-HCJ-series CJ1GXM2S-251125-pinMade by OMRONCV500-LK201C200H-LK201-EV1AWG28 5PIFVV-SBMulti-core shielded cableMade by Fujikura, Ltd.---CO-MA-VV-SB5P 28AWGMulti-core shielded cableMade by Hitachi Cable,Ltd.---Note After connecting a communication cable, always secure it with the screws.Otherwise the cable may disconnect, causing operation to fail.OMRON Cables with ConnectorsThe OMRON cables listed below can be used when connecting with a methodother than the memory link method.ModelCable LengthXW2Z-200S2mXW2Z-500S5mXW2Z-200T2mXW2Z-500T5mConnector Specification9 pin ⇔ 25 pin9-pin9 pin ⇔ 9-pin9 pin9-pinThe OMRON cable listed below can be used when connecting to a personalcomputer with the memory link method.ModelXW2Z-S002Cable LengthConnector Specification2m9-pin ⇔ 9 pinNote The cable’s tensile load is 30 N.
Do not subject it to loads greater than this.Otherwise a discontinuity may occur, causing operation to fail.Wiring for a Host LinkUnit (25-pin) ConnectionApplicable Units: C200H-LK201-EV1CV500-LK201 (communication port 1)Compatible cables with attached connectors:XW2Z-200S (9-pin ⇔ 25-pin, 2 m)XW2Z-500S (9-pin ⇔ 25-pin, 5 m)CVM1/CV-series Host Link Units (CV500-LK201) have two types of connector; a25-pin connector (communication port 1), and a 9-pin connector (communica-64SectionConnecting to the RS-232C Port at the Host4-1tion port 2).
When using communication port 2, refer to Wiring for Other Connections (Other Than the Memory Link Method) (page65).16NT21AbbreviationFGRS-232CinterfacePC (Host Link Unit)PinnumberConnectorhood12SD23RDRD34RSRS45CSCS5+5V659(9-pin type)141325PinAbbreviationnumberConnectorFGhoodShieldSD5G1*6–75G78–8––9–––––ERRS-232Cinterface(25-pin type)* For Units that have a CTS setting selector switch, RS and CS do not have to beshorted if this switch is set to 0V.Wiring for OtherConnectionsApplicable Units:CV500-LK201 (communication port 2)CS1W-SCU21CJ1W-SCU41CPM1-10CDR-jCPM1-20CDR-jCPM1-30CDR-jCPM1A-10CDj-jCPM1A-20CDj-jCPM1A-30CDj-jCPM1A-40CDj-jCPM2A-30CDj-jCPM2A-40CDj-jCPM2A-60CDj-jCPM2C-10jjjjjj-j CPM2C-20jjjjjj-jCQM1-CPU21-ECQM1-CPU41-EV1CQM1-CPU42-EV1CQM1-CPU43-EV1CQM1-CPU44-EV1CQM1H-CPU11CQM1H-CPU21CQM1H-CPU51CQM1H-CPU61CS1G-CPU42-E(V1)CS1G-CPU43-E(V1)CS1G-CPU44-E(V1)CS1G-CPU45-E(V1)CS1H-CPU63-E(V1)CS1H-CPU64-E(V1)CS1H-CPU65-E(V1)CS1H-CPU66-E(V1)CS1H-CPU67-E(V1)CS1G-CPU42HCS1G-CPU43HCS1G-CPU44HCS1G-CPU45HCS1H-CPU63HCS1H-CPU64HCS1H-CPU65HCS1H-CPU66HCS1H-CPU67HCJ1G-CPU44CJ1G-CPU45C200HS-CPU21-E, -ECC200HS-CPU23-EC200HS-CPU31-EC200HS-CPU33-EC200HE-CPU32-(Z)EC200HE-CPU42-(Z)EC200HG-CPU33-(Z)EC200HG-CPU43-(Z)EC200HG-CPU53-(Z)EC200HG-CPU63-(Z)EC200HX-CPU34-(Z)EC200HX-CPU44-(Z)EC200HX-CPU54-(Z)EC200HX-CPU64-(Z)EC200HX-CPU65-ZEC200HX-CPU85-ZECVM1-CPU01-EV2CVM1-CPU11-EV2CVM1-CPU21-EV2SRM1-C02-V265SectionConnecting to the RS-232C Port at the Host4-1Compatible cables with attached connectors:XW2Z-200T (9-pin ⇔ 9-pin, 2 m)XW2Z-500T (9-pin ⇔ 9-pin, 5 m)CPU Units of CVM1/CV-series PCs without the suffix -EVj cannot be connected by any connection method.16NT21PC (Host Link Unit)PinAbbreviation numberConnectorFGhoodRS-232Cinterface59Wiring for a Memory LinkConnection659PinAbbreviationnumberConnectorFGhoodShield–12SDSD23RDRD34RSRS45CSCS56–+5V67–78–––89SG9*RS-232CinterfaceSG(9-pin type)(9-pin type)Compatible cables with attached connectors:XW2Z-S002 (9-pin⇔9-pin, 2 m)Prepare the adapter cable while referring to the following diagram.PC (Host Link Unit)NT2116Abbreviation Pin numberRS-232Cconnector56619ShieldAbbreviationConnectorhoodFGConnectorhood–1SDSD2RDRD3RSRS4CSCS5SG+5V6–7–8SG9(9-pin type)RS-232CconnectorSECTION 5Connecting to the Host from the RS-422A/485 PortThis section describes how to connect to the host using RS-422A/485 cable.
Link Adapters convert communication signalsbetween RS-232C cable and RS-422A/RS-485 cable.5-15-2Connecting to the Host’s RS-422A/485 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1-1 Host Types and Settings . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .5-1-2 Direct 1:1 Connection to the Host’s RS-422A . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1-3 Direct 1:1 Connection to the Host’s RS-485 . . . . . . . . . . . . . . . .
. . . . . . . . . . . . .5-1-4 1:N Connection to the Host’s RS-422A Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1-5 1:N Connection to the Host’s RS-485 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1-6 Recommended Connectors, Cables and Crimp Terminals . . .
. . . . . . . . . . . . . . .Connecting to the Host’s RS-232C Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2-1 Host Types and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2-2 1:N Connection Using the Host’s RS-232C Port . . . . . . . . .
. . . . . . . . . . . . . . . . .5-2-3 Recommended Connectors, Cables, and Crimp Terminals . . . . . . . . . . . . . . . . . .686985888992949495959967SectionConnecting to the Host’s RS-422A/485 Port5-15-1Connecting to the Host’s RS-422A/485 PortThis section explains how to connect to the host’s RS-422A/485 port through anRS-422A/485 cable.
There are 4 ways to connect through RS-422A/485 cable.This explanation focuses on connections to OMRON PCs, although anyRS-422A device can be connected using the memory link method.• Method 1This is a 1:1 connection between the PT’s RS-232C port and host’s RS-422Aterminals (using RS-422A cable) through a Link Adapter. The communicationscable can be extended up to 500 m long with this method.PTLinkAdapterHostRS-422A cable(500 m max.)RS-232C cable(2 m max., notrequired with theNS-AL002.)• Method 2This is a 1:1 connection between the PT’s RS-232C port and host’s RS-485terminals (using RS-485 cable) through a Link Adapter.
The communicationscable can be extended up to 500 m long with this method.PTHostLinkAdapterRS-485 cable(max. 500 m)RS-232C cable(2 m max., notrequired with theNS-AL002.)• Method 3This is a 1:N connection between the RS-232C ports on several PTs and thehost’s RS-422A terminals (using RS-422A cable) through Link Adapters. Thecommunications cable can be up to 500 m long with this method.This connection method can only be used with the 1:N NT Link (standard orhigh-speed).PTLink AdaptersHostRS-422A cable(total length 500 m max.)RS-232C cable(2 m max., notrequired with theNS-AL002.)• Method 4This is a 1:N connection between the RS-232C ports on several PTs and thehost’s RS-485 terminals (using RS-485 cable) through Link Adapters.
The68SectionConnecting to the Host’s RS-422A/485 Port5-1communications cable can be up to 500 m long with this method. This connection method can only be used with the 1:N NT Link (standard or high-speed).PTHostLink AdaptersRS-485 cable(Total length 500 m max.)RS-232C cable(2 m max., notrequired with theNS-AL002.)Note One end of the wire must always be connected to the host (PC), and there mustbe no branching. Branching will cause problems such as transmission delaysand communication failures.PC(Terminated)PCPCRelay Terminal BlockRelay Terminal BlockMax.
2 mNT21NT21(Notterminated)(Notterminated)NT21NT21NT21NT21NT21NT21NT21NT21(Terminated)(Notterminated)Example of Good ConnectionExamples of Bad ConnectionsReference: CS/CJ-series CPU Units cannot be connected with the 1:1 connection NT linkmethod. Use the 1:N connection NT link method (standard or high-speed)instead of making the 1:1 connection. For details, refer to Using the 1:N NT LinkMethod (page 80) or Using the High-speed 1:N NT Link Method (page 83).5-1-1 Host Types and SettingsThis section lists the hosts that have RS-422A ports that can be connected to aPT and describes the settings required at the host.When Using the Host Link MethodCompatible Host UnitsSome models and series of OMRON PCs have the RS-422A type Host Linkfunction built in.
With a CS series, CJ series, and CQM1H Board or Unit, andCQM1H, the Host Link method can be used by installing a Serial Communications Board. In addition, some C200HX/HG/HE(-Z)E devices have an integralCPU Unit that can be connected in the Host Link method by installing a SerialCommunications Board.With the CPM2A and CPM2C, an RS-422A type of 1:1 NT Link can be connected through a CPM1-CIF11 RS-422A Adapter.Check the model and series of the PC and the type of the installed Board or Unitbefore making a connection.69SectionConnecting to the Host’s RS-422A/485 Port5-1The following table lists the Units that are equipped with an RS-422A Host Linkfunction compatible with the NT21.Units with Built-in Host Link FunctionPC SeriesHost Link Unit /Serial CommunicationsBoardCPU Units Connectable withHost Link Units or Expansion Serial Communications BoardCPU UnitConnectabletoCS SeriesCS1W-SCB41-E---CS1G-CPU42/43/44/45-EV1CS1H-CPU63/64/65/66/67-EV1CS1G-CPU42H/43H/44H/45HCS1H-CPU63H/64H/65H/66H/67HCJ SeriesCJ1W-SCU41---CJ1G-CPU44/45CJ1G---C200HS-CPU01/03/21/23/31/33-EC200HS-CPU01/21-ECC200HE-CPU11/32/42-EC200HE-CPU11/32/42-ZEC200HG-CPU33/43/53/63-EC200HG-CPU33/43/53/63-ZEC200HX-CPU34/44/54/64-EC200HX-CPU34/44/54/64/65/85-ZEC200HSC200HEC200HE-ZEC200HGC200HG-ZEC200HXC200HX-ZEC200HE-CPU32/42-EC200HE-CPU32/42-ZEC200HEC200HE-ZEC200HG-CPU33/43/53/63-EC200HG-CPU33/43/53/63-ZEC200HGC200HG-ZEC200HX-CPU34/44/54/64-EC200HX-CPU34/44/54/64/65/85-ZEC200HXC200HX-ZE---CPM1C200H-LK202-V1C200HW-COM03/06-EV1---C SeriesCPM1-10/20/30CDR-j+CPM1-CIF11---CPM1A-10/20/30/40CDj-j+CPM1-CIF11CS1GCS1HCS1G-HCS1H-H---CPM2A-30/40/60CDj-j+CPM1-CIF11(Peripheral port connection)---CPM2A---CPM2C-10/20jjjjjj-j (*1)---CPM2CCQM1H-SCB41---CQM1H-CPU51/61CQM1HCVM1 Series (*2)CV500-LK201CVM1-CPU01-EV2CVM1-CPU11-EV2CVM1-CPU21-EV2CVM1-CPU01-EV2CVM1-CPU11-EV2CVM1-CPU21-EV2CVM1SRM1---SRM1-C02-V1+CPM1-CIF11---SRM1*1: Use a CPM2C-CN111 or CS1W-CN114/118 Connecting Cable, CPM1-CIF01 RS-232C Adapter, or CPM1-CIF11RS-422A Adapter to connect.*2: CPU Units of CVM1/CV-series PCs without the suffix -EVj cannot be connected.The Host Link method cannot be used when an NT21 is connected usingRS-485.