CPM2A_OPERATION MANUAL (W352-E1-3) (986749), страница 28
Текст из файла (страница 28)
When downloading, notethe following points.155SectionHandling! CautionNoteIf the PC is in RUN or MONITOR mode when downloading is started, it will automatically switch to PROGRAM mode and operation will stop. Confirm that noadverse effects will occur to the system before downloading. Not doing so mayresult in unexpected operation.1. If the PC is in RUN or MONITOR mode, switch the PC mode to PROGRAMmode.2. Confirm that the program or other data to be downloaded to the PC is compatible with the PC before downloading.3. For the CQM1 or CQM1H, when downloading programs that use user-assigned function codes for expansion instructions, be sure that pin 4 on theCPU Unit’s DIP switch is ON.
If these programs are downloaded while thepin is OFF, the assignments for the expansion instructions will return to theirdefault settings.4. After downloading has been completed, be sure to confirm the user program, data, and expansion instructions.5. When the DOWNLOAD TO PLC Button is pressed, all EEPROM data (ladder programs, data memory etc.) is written to the PC.Expansion Memory UnitIndicator1566-3SYSMAC PCDOWNLOAD TO PLC ButtonSectionHandling6-3Operation ProcedureStartMount the EEPROM to theCPM1-EMU01-V1.Mount the EEPROM to theCPM1-EMU01-V1 before downloading.Change the mode of the PC to PROGRAM mode.Confirm the safety of the system.Connect the CPM1-EMU01-V1 to thePC’s peripheral port.Confirm the orientation of the connectorbefore connecting the CPM1-EMU01-V1.After 2 or 3 s, check if the indicator islit green.NoNote If the indicator is not lit at all, lit red orSee the note onthe right.• Is the connector properly connected?YesPress the DOWNLOAD TO PLC Button.• Is the EEPROM properly mounted?• Are the EEPROM specifications correct?• Are the peripheral port communications settings correct?Check if the indicator is blinkinggreen (indicating that downloadinghas started).Noblinks red, downloading will not bepossible.
In this case, check the following items.See the note above.YesCheck if the indicator is lit green(indicating that downloading hasbeen successfully completed).NoSee the note above.YesRemove the Expansion Memory Unitfrom the PC.Check the program.Before actual operation, check the contentsof the ladder program and the DM area, aswell as the expansion instruction settings.End157Appendix AStandard ModelsCPU UnitsDescriptionInputpointsCPU Units with 20 I/O points 12 pointsCPU Units with 30 I/O points 18 pointsCPU Units with 40 I/O points 24 pointsCPU Units with 60 I/O points 36 pointsOutputpoints8 points12 points16 points24 pointsPowersupplyModel numberRelay outputsTransistor outputsSinkingSourcing-----ACCPM2A20CDR-ADCCPM2A20CDR-DCPM2A20CDT-DCPM2A20CDT1-DACCPM2A30CDR-A------DCCPM2A30CDR-DCPM2A30CDT-DCPM2A30CDT1-DACCPM2A40CDR-A------DCCPM2A40CDR-DCPM2A40CDT-DCPM2A40CDT1-DACCPM2A60CDR-A------DCCPM2A60CDR-DCPM2A60CDT-DCPM2A60CDT1-DExpansion I/O UnitsDescriptionModel numberInputpointsOutputpointsExpansion I/O Unit with 20 I/O points12points8 points CPM1A-20EDR1Expansion I/O Unit with 8 input points8 points ---Expansion I/O Unit with 8 output points---Relay outputTransistor outputSinkingSourcingCPM1A-20EDTCPM1A-20EDT1CPM1A-8ED (no outputs)8 points CPM1A-8ERCPM1A-8ETCPM1A-8ET1159Appendix AStandard ModelsExpansion UnitsAnalog I/O UnitDescriptionAnalog I/O UnitSpecificationsModel number2 analog inputs and 1 analog outputCPM1A-MAD01Temperature Sensor UnitsDescriptionTemperature Sensor UnitSpecificationsModel number2 thermocouple inputs: K, J4 thermocouple inputs: K, J2 platinum resistance thermometer inputs:Pt100 (100 Ω), JPt100 (100 Ω)4 platinum resistance thermometer inputs:Pt100 (100 Ω), JPt100 (100 Ω)CPM1A-TS001CPM1A-TS002CPM1A-TS101CPM1A-TS102CompoBus/S I/O Link UnitDescriptionCompoBus/S I/O Link UnitSpecificationsModel numberOperates as a CompoBus/S Slave and provides 8inputs and 8 outputs to the CPM1A or CPM2A PC.CPM1A-SRT21Adapters and Connecting Cables (1:1 Connection)CPM2A portPeripheralRS-232C160NameRS-232CAdapterRS-232CCableAppearanceModel numberCommentsCable lengthCQM1-CIF01For a 25-pin computer serial port3.3 mCQM1-CIF02For a 9-pin computer serial port3.3 mCPM1-CIF01 (+XW2Z-j00S)For a 25-pin computer serial port3.3 m (+ j m)XW2Z-200SXW2Z-500SXW2Z-200S-VXW2Z-500S-VFor a 25-pin computer serial port2m5m2m5mFor a 9-pin computer serial portAppendix AStandard ModelsAdapters and Connecting Cables (1:N Connections)NameAppearanceModel numberSpecificationsRS-422 AdapterNT-AL001Use for CPM2A RS-232C port to RS-422A conversion.Requires a 5-VDC, 150 mA power supply which issupplied through the CPM2A connection.(Can also be connected to a personal computer, but thisconnection requires an external 5-VDC power supply.)Link AdapterB500-AL004Use for personal computer RS-232C port to RS-422A.(Can also be connected to a CPM2A.)RS-422 AdapterCPM1-CIF11Use for CPM2A peripheral port to RS-422A conversion.RS-232C CablesXW2Z-070T-1(For use with theNT-AL001.)XW2Z-070T-1Use for CPM2A RS-232C port to NT-AL001 connection.(70-cm cable)Use for CPM2A RS-232C port to NT-AL001 connection.(2-m cable)161Appendix AStandard ModelsPeripheral DevicesNameProgramming ConsoleAppearanceModel NumberSpecificationsCQM1-PRO01-E2-m Connecting Cable attachedC200H-PRO27-EHand-held, w/backlight; requires aC200H-CN222 or C200H-CN422Connecting Cable, see below.C200H-CN222Connects theC200H-PRO27-E toa peripheral port.C200H-CN4222-m cable4-m cableCX-ProgrammerWS02-CXPC1-EFor MS-Windows 95/98 (CD-ROM)SYSMAC Support SoftwareC500-ZL3AT1-E3.5”, 2HD for IBM PC/AT compatibleSYSMAC-CPTWS01-CPTB1-EFor IBM PC/AT or compatible computers(3.5” disks (2HD) and CDROM)Connecting CableC200H-CN222Expansion Memory UnitCPM1-EMU01-V1Connects C200H Programming Console toPeripheral Port (2 m)Connects C200H Programming Console toPeripheral Port (4 m)Uploads the ladder program and DM 6144to DM 6655 from the PC to the EEPROMand downloads the ladder program andDM 6144 to DM 6655 from the EEPROMto the PC.EEPROMEEROM-JD256 K bitC200H-CN422Maintenance AccessoriesNameBackup Battery162AppearanceModel NumberCPM2A-BAT01Specifications---Appendix BDimensionsAll dimensions are in millimeters.CPM2A-20CDj-j CPU UnitsFour, 4.5 dia.NCNCNCNCCPU Units with DC PowerCPU Units with AC PowerCPU Units with DC PowerCPU Units with AC PowerNCNCNCNCNCNCNCCPM2A-30CDj-j CPU UnitsFour, 4.5 dia.163Appendix BDimensionsCPM2A-40CDj-j CPU UnitsFour, 4.5 dia.CPU Units with DC PowerCPU Units with AC PowerCPM2A-60CDj-j CPU UnitsFour, 4.5 dia.CPU Units with DC Power164CPU Units with AC PowerAppendix BDimensionsCPM1A-20EDj Expansion I/O UnitsFour, 4.5 dia.CPM1A-8jjj Expansion I/O UnitsFour, 4.5 dia.CPM1A-MAD01 Analog I/O UnitFour, 4.5 dia.165Appendix BDimensions100 ± 0.2CPM1A-TSjjj Temperature Sensor Units76±0.2Four, 4.5 dia.CPM1A-SRT21 CompoBus/S I/O Link UnitFour, 4.5 dia.166DimensionsAppendix BCPM1-CIF01 (RS-232C Adapter)167DimensionsCPM1-CIF11 (RS-422 Adapter)168Appendix BAppendix BDimensionsDimensions with Programming Devices AttachedCPU Units with DC PowerApprox.
95CPU Units with AC PowerApprox. 130CPM1-CIF01 RS-232C AdapterApprox. 120169IndexNumbers1:1 communications, 771:N communications, 79AAnalog I/O Unit, standard model, 160analog volume controls, location, 37arc killer, examples, xviiASCII, converting displays, Programming Console, 122computer, connecting, 77conduit installation, 50counterschanging SV, Programming Console, 117example of inputting, 127CPM1A, function comparison, 18CPU Unitsavailable models, 8, 159cyclic operation, 13internal structure, 10standard models, 159cycle time, displaying, Programming Console, 123cyclic operation, 13atmosphere, 28BDbattery, replacing, 146data, modifying, Programming Console, 116–117, 118, 119,120binary data, modifying, Programming Console, 119data link, 5, 81bit status, force-set/reset, Programming Console, 121date.
See clockbits, searching, Programming Console, 109decimal data with sign. See signed decimal databuzzer operation, Programming Console, 103decimal data without sign. See unsigned decimal datadielectric strength, 28Ccabinetinstallation, precautions, 45Programming Console installation, 98cables, available models, 160characteristics, 29check levels, program checks, 136checking, program syntax, Programming Console, 111circuit configurationinputs, 31outputs, relay, 33differentiated instructions, entering, 107dimensions, 163DIN Track installation, 47displaysconverting between hex and ASCII, Programming Console,122cycle time, Programming Console, 123downloading, programs, 155duct installation, 49Eclearing, memory areas, Programming Console, 102EC Directives, precautions, xvclock, reading and setting the clock, 123EEPROMmounting/removing, 152specifications, 151communication errors, 135communications capabilities, 18overview, 4electrical noise, preventing, 45, 49CompoBus/S I/O Unit, standard model, 160ERR/ALM indicatorflashing, 134lit, 135componentsAnalog I/O Unit, 39CompoBus/S I/O Link Unit, 41CPU Unit, 35Expansion I/O Unit, 38Temperature Sensor Unit, 39errorscommunications, 135error processing, 131fatal, 135identifying, 133non-fatal, 134CompoBus/S I/O Link, 81171Indexprogramming, 136Programming Console operations, 136reading/clearing messages, Programming Console, 103user-defined errors, 134Expansion I/O Unitsavailable models, 9, 159components, 38connection, 48standard models, 159expansion instructions, reading and changing function codeassignments, 104Expansion Memory Unit, 149connections, 153Expansion Unitsavailable models, 9, 160connection, 48PC status indicators, 36inductive loads, 61, 75initialization, time required, 12input devices, connecting, 59input specifications, 31, 32inputs, wiring, 54configuration, 54inrush current, suppressing, 75inspections, 145installation, 46site, selecting, 44instructionsinserting and deleting, Programming Console, 110searching, Programming Console, 108insulation resistance, 28interlocks, 44FFAL numbers, 134FAL(06), 134interrupt program execution, in cyclic operation, 15L–MFALS numbers, 135leakage current, 61FALS(07), 134limit switches, preventing false inputs, 61false inputs, 61machine control functions, list, 16fatal errors, troubleshooting, 139features, 2flash memory, precautions, 132flicker output, example, 128maintenance, 145memorybackup, 30Expansion Memory Unit, 149protection, 30force-set/resetclearing, Programming Console, 122Programming Console, 121memory areasclearing, Programming Console, 102partial clear, 102uploading/downloading, 150function codes, reading and changing expansion instructionassignments, 104messages, reading/clearing, 103functions, 7mode, changing the PC mode, 97model numbers, 159modes, operating modes, 11G–Hgrounding, 36, 51hexadecimal data, converting displays, Programming Console,122Host Link, connections, 77II/O capacity, 29I/O errors, troubleshooting, 141I/O line noise, preventing, 49indicatorsCompoBus/S LED indicators, 41flashing ERR/ALM indicator, 134lit ERR/ALM indicator, 135172modifyingbinary data, Programming Console, 119data, Programming Console, 116hexadecimal/BCD data, Programming Console, 118signed decimal data, Programming Console, 119SV, Programming Console, 117unsigned decimal data, Programming Console, 120MONITOR modedescription, 89, 97example test run, 129monitoring3-word monitor, Programming Console, 115binary monitor, Programming Console, 114–115differentiation monitor, Programming Console, 113–114signed decimal monitor, Programming Console, 115–116status, Programming Console, 111unsigned decimal monitor, Programming Console, 116motor control, capabilities, 3MSG(46), 134IndexNgeneral, xiuploading/downloading, 150no-protocol communications, 80program, programming example, 124noise, preventing electrical noise, 45, 49program capacity, 29noise immunity, 28program execution, in cyclic operation, 14non-fatal errors, troubleshooting, 140program memory, setting address and reading content, Programming Console, 105NPN current output, connecting, 59NPN open collector, connecting, 59NT Link, connections, 80Ooperating conditions, troubleshooting, 143operating modes, 11operating mode at startup, 11operation, preparations, 99output short protection, 74output specificationsrelay output, 33transistor output, sink type, 34output wiringconfiguration, 63, 66, 70relay output, 62transistor outputsink type, 66source type, 70PPROGRAM mode, description, 89, 97programmingchecking the program, 129checks for syntax, Programming Console, 111errors, 136inserting and deleting instructions, Programming Console,110–111preparation for, 124searching, Programming Console, 108–109setting and reading a memory address, Programming Console, 105Programming Consoleconnecting, 76, 98keys, 95models, 95operations, 101Programming Devicesconnecting, 76using, 83programming example, 124programschecking, check levels, 136downloading, 155entering and editing, Programming Console, 105uploading, 154proximity switches, preventing false inputs, 61panel, Programming Console installation, 98pulse control, 3panel installation, precautions, 45pulse outputs, 3wiring, 74password, entering on Programming Console, 99PC mode, changing, 97PC Status, indicators, 36Peripheral Devices, 162available models, 162photoelectric switches, preventing false inputs, 61Q–Rquick-response inputs, 4relay outputs, connecting, 59RUN mode, description, 89, 97PNP current output, connecting, 59position control, 3power, consumption, 28power cables, 49power interruption, detection, 12Ssearchinstruction, Programming Console, 108–109operands, Programming Console, 109power supplycapacity, 28interrupt time, 28precautions, 44troubleshooting, 138, 144wiring, 52self-diagnosis functions, 30precautionsdesign precautions, 44shock resistance, 28self-holding bit, example, 126self-diagnostic functions, 133serial communications, 80signed decimal data173Indexmodifying, Programming Console, 119monitoring, 115–116specificationscharacteristics, 29Expansion Memory Unit, 151general specifications, 28input specifications, 31, 32output specificationsrelay output, 33transistor output, sink type, 34SSS, 92status, monitoring, Programming Console, 111Support Software, 76, 84SV, modifying, Programming Console, 117terminals, screw size, 28test runexample, 129procedure, 132time.