CPM2A_OPERATION MANUAL (W352-E1-3) (986749), страница 18
Текст из файла (страница 18)
Mnemonics will be displayed, however, if any have beendefined for the specified function code.When the program is transferred from the SSS to the PC, TKY, MCMP, DSW,and 7SEG will be displayed on the SSS, but will not be executed in the CPU Unit.They will be treated as NOP.If expansion instructions are transferred to the PC with DM 6602 is set to the “default settings,” a message saying that expansion instructions cannot be writtenbecause DIP switch pin 4 is OFF will be displayed. Change the setting ofDM 6602 to enable user settings to use expansion instructions. If instructionsnot supported by the CPM2A are transferred to the PC, a message saying to setexpansion instructions will be displayed, and transfer will not be possible.93SectionSYSMAC Support Software (SSS)Expansion Instructions4-2It will not be possible to transfer the program if the function codes assigned toexpansion instructions have been changed from their default settings.
A message to turn ON the DIP switch of the PC and execute again will be displayed.Change the function code assignments to the CQM1 defaults shown in the following table before programming.Function codeDefault CPM2A Assignments17ASFTASFTDefault CQM1 Assignments18---TKY19---MCMP47RXDRXD48TXDTXD60CMPLCMPL61INIINI62PRVPRV63CTBLCTBL64SPEDSPED65PULSPULS66SCLSCL67BCNTBCNT68BCMPBCMP69STIMSTIM87---DSW88---7SEG89INTINTIf a CQM1 instruction that is not supported by the CPM2A is used in the program,an error will occur when the program is transferred from the computer to the PC.There are four CPM2A instructions (STUP(––), SYNC(––), TIML(––), andTMHH(––)) that are not supported by the CQM1.
These instructions can be usedby transferring the expansion instructions from the CPM2A to the SSS. This procedure is outlined below.1, 2, 3...1. Select “Transfer Instr” from the “Utility” menu.2. Confirm the transfer by pressing “Y” when the confirmation pop-up is displayed.3.
The “Utility” menu will be displayed again when the transfer is completed.PC Setup94Since some of the CPM2A’s PC Setup settings are different from those in theCQM1, not all settings can be made from the menus. These settings have to bemade by writing data directly to the word containing the setting.SectionUsing a Programming Console4-34-3Using a Programming ConsoleThis section provides information on connecting and using a Programming Console. Refer to 5-3 Programming Console Operation Errors for details on errorsthat might occur during Programming Console operations.4-3-1 Compatible Programming ConsolesThere are two Programming Consoles that can be used with the CPM2A: TheCQM1-PRO01-E and the C200H-PRO27-E. The key functions for these Programming Consoles are identical.Press and hold the Shift Key to input a letter shown in the upper-left corner of thekey or the upper function of a key that has two functions.
For example, theCQM1-PRO01-E’s AR/HR Key can specify either the AR or HR Area; press andrelease the Shift Key and then press the AR/HR Key to specify the AR Area.CQM1-PRO01-ELCD displayAttached ConnectingCable (2 m)Mode switchOperation keysC200H-PRO27-ELCD displayMode switchOperation keysCassette recorded jack(Cannot be used with the CPM2A).Connecting CablesC200H-CN222 (2 m)C200H-CN422 (4 m)95SectionUsing a Programming ConsoleDifferent Keys4-3The following keys are labeled differently on the CQM1-PRO01-E and theC200H-PRO27-E, but the operation of the keys in each pair is identical.CQM1-PRO01-E KeysC200H-PRO27-E KeysARHRHRPLAYSETSETRECRESETRESETNote To specify the AR area, use SHIFT and HR Keys for the C200H-PRO27-E anduse SHIFT and AR/HR Keys for the CQM1-PRO01-E.A shift symbol will be displayed in the upper-right corner of the screen when theShift Key is pressed.
The shift input can be cleared by pressing the Shift Keyagain.^SHIFTShift inputsymbolMode SwitchThe mode switch controls the CPM2A’s operating mode. The key can be removed when the switch is set to RUN or MONITOR but it cannot be removedwhen the switch is set to PROGRAM.Contrast ControlThe display contrast can be adjusted with the control on the right side of the Programming Console.Contrast controlBuzzer VolumeThe C200H-PRO27-E’s buzzer volume can be adjusted with the lever on theright side of the Programming Console.
The CQM1-PRO01-E’s buzzer volumecannot be adjusted.Low volumeHigh volumeC200H-PRO27-ENote The buzzer volume can be turned on and off with a key operation. See 4-4-4Buzzer Operation for details.96SectionUsing a Programming Console4-34-3-2 Changing the CPM2A’s Mode with the Mode SwitchOnce the Programming Console has been connected, its mode switch can beused to change the CPM2A’s operating mode. The mode display (<PROGRAM>, <MONITOR>, or <RUN>) will appear on the Programming Consolescreen.• No key operations can be performed while the mode display is displayed onthe Programming Console screen.
Press CLR to clear the display so that keyoperations can be performed.• If the SHIFT Key is pressed while the mode switch is turned, the original display will remain on the Programming Console’s screen and the mode displaywon’t appear.• The CPM2A will enter RUN mode automatically if a Programming Consoleisn’t connected when the CPM2A is turned on.MONITORRUNPROGRAMMONITORRUNPROGRAMMONITORRUNPROGRAMMode display<PROGRAM>BZOperation<MONITOR>CLRInitial displayBZOperation<RUN>SHIFTBZCLR00000Operating ModesPROGRAM ModeThe CPM2A program isn’t executed in PROGRAM mode.
Use PROGRAMmode to create and edit the program, clear memory, or check the program forerrors.MONITOR ModeThe CPM2A program is executed in MONITOR mode and I/O is processed justas it is in RUN mode. Use MONITOR mode to test system operations, such asmonitoring CPM2A operating status, force-setting and resetting I/O bits, changing the SV/PV of timers and counters, changing word data, and online editing.RUN ModeThis is the CPM2A’s normal operating mode. The CPM2A’s operating status canbe monitored from a Programming Device, but bits can’t be force-set/force-resetand the SV/PV of timers and counters can’t be changed.! CautionCheck the system thoroughly before changing the operating mode of the PC toprevent any accidents that might occur when the program is first started.! CautionNever change the mode while pressing any of the keys.97SectionUsing a Programming ConsoleStartup Operating Mode4-3The operating mode of the CPM2A when the power is turned ON depends uponthe PC Setup setting in DM 6600 and the Programming Console’s mode switchsetting if the Programming Console is connected.PC Setup setting(DM 6600)00000200Programming Console notconnectedRUN mode if no Programming Deviceis connected.
PROGRAM mode ifanother Programming Device isconnected.The startup mode is the same as the operating mode beforepower was interrupted.PROGRAM mode0201MONITOR mode0202RUN mode0100ProgrammingConsole connectedThe startup modedetermined by themode switch setting.Note The default setting is 0000. If a Programming Console is not connected, the PCwill automatically enter RUN mode.
Be sure that it is safe for the PC to operatebefore turning on the PC without a Programming Console connected.4-3-3 Connecting the Programming ConsoleConnect the Programming Console’s connecting cable to the CPM2A’s peripheral port, as shown below.Panel InstallationThe C200H-PRO27-E Programming Console can be installed in a control panelas shown in the following diagram. (The C200H-ATT01 Mounting Bracket is soldseparately.)Mounting BracketMounting hole dimensions(DIN43700 standards)Two screws+1.1186 –0Panel thickness: 1.0 to 3.2 mm9892 +0.8–0SectionUsing a Programming Console4-3Allow at least 80 mm for the cable connector above the Programming Console.3715At least 80 mm is required.Either connector maybe used.About 70 mm is required.4-3-4 Preparation for OperationThis section describes the procedures required to begin Programming Consoleoperation when using the Programming Console for the first time.! CautionAlways confirm that the Programming Console is in PROGRAM mode whenturning ON the PC with a Programming Console connected unless anothermode is desired for a specific purpose.
If the Programming Console is in RUNmode when PC power is turned ON, any program in Program Memory will beexecuted, possibly causing a PC-controlled system to begin operation.The following sequence of operations must be performed before beginning initial program input.1, 2, 3...1. Be sure that the PC is OFF.2.
Connect the Programming Console to the CPU Unit’s peripheral port. See4-3-3 Connecting the Programming Console for details.(The CPU Unit’s Communications Switch setting has no effect on communications with the Programming Console.)3. Set the mode switch to PROGRAM mode.4. Turn ON the PC.5. Enter the password. See 4-3-5 Entering the Password for details.6. Clear (All Clear) the PC’s memory. See 4-4-2 Clearing Memory for details.7. Read and clear all errors and messages. See 4-4-3 Reading/Clearing ErrorMessages for details.8. Start programming.4-3-5 Entering the PasswordTo gain access to the PC’s programming functions, you must first enter the password.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
