H126-E2-02 E5CN(-U) Datasheet (Техническая документация), страница 3

Refer to page 3.E5CN-UVoltage Output−5DC12VControl output 1 421mA+Relay OutputOne Alarm OutputBBPt0 to 50 mV input onlyPlatinumresistancethermometer784A−Analog input+653−921Do not use.1011 Input power supply+TCInfrared temperature sensorThe input power supply depends on the power supply specification of theController and is either 100 to 240 VAC or 24 VAC/DC (no polarity).Order the P2CF-11 or P3GA-11 Socket separately. (See page 13.)10Alarm 1/Input error output(See note.)Digital Temperature Controllers E5CN/E5CN-UTwo Alarm Outputs789Alarm 1/Input error outputAlarm 2/Control output 2Note: Output when an input error output isenabled in the Advance FunctionSetting Level.

If an input erroroutput is enabled, the al-1operation indication on the frontpanel will not light and s.err will bedisplayed on the No. 1 display.NomenclatureE5CNE5CN-UThe front panel is the same for the E5CN and E5CN-U.Temperature unitNo.1 displayOperation indicatorsNo. 2 displayUp KeyLevel KeyMode KeyDown KeyDimensionsE5CNTerminal ModelsPanel CutoutGroup MountedMounted Separately(48 × number of units −2.5) +1.0091648 × 487845 +0.6044.8 × 44.8 48.858Group mounting does notallow waterproofing.60 min.45 +0.60Mounting Adapter(Accessory)Terminal Cover(E53-COV10)45 +0.60Note: The terminal block cannot be removed.The suffix “-500” is added to the model numberof each Controller provided with a E53-COV10Terminal Cover.E5CN-UPlug-in Models• Recommended panel thickness is 1 to5 mm.• Group mounting is not possible in thevertical direction. (Maintain thespecified mounting space betweenControllers.)• To mount the Controller so that it iswaterproof, insert the waterproofpacking onto the Controller.• When two or more Controllers aremounted, make sure that thesurrounding temperature does notexceed the allowable operatingtemperature specified in thespecifications.Panel CutoutGroup MountedMounted Separately(48 × number of units −2.5) +1.00648 × 4814.270.545 +0.6044.8 × 44.85860 min.45 +0.60Mounting Adapter(Accessory)45 +0.60Digital Temperature Controllers• Recommended panel thickness is 1 to5 mm.• Group mounting is not possible in thevertical direction.

(Maintain thespecified mounting space betweenControllers.)• When two or more Controllers aremounted, make sure that thesurrounding temperature does notexceed the allowable operatingtemperature specified in thespecifications.E5CN/E5CN-U11■ AccessoriesUSB-Serial Conversion Cable (Sold Separately)E58-CIFQ1(2,100)LED indicator (SD)250USB connector (type A plug)1,765Serial connectorLED indicator (RD)Terminal Cover48E53-COV1048.822Note: The suffix “-500” is added to the model number of eachController provided with a E53-COV10 Terminal Cover.9.1Current Transformers (Sold Separately)E54-CT121152.85.8 dia.7.525310.540Two, 3.5 dia.1030E54-CT3 AccessoryE54-CT32.36 dia.Connection Example• Armature30ArmaturePlug12 dia.9Approx. 3 dia.Lead40 × 4018• PlugTwo, M3 (depth: 4)Approx.

6 dia.153012Digital Temperature Controllers E5CN/E5CN-U(22)Adapter (Sold Separately)Note: Use this Adapter when the panel has already been prepared for the E5B@.Y92F-45Fixture (Accessory)764.769.6 to 77.672 × 7267 × 67 87Mounted to E5CNPanel (1 to 8 mm)72 × 7248 × 482.24.777.3 (to back of E5CN)E5CN-U Wiring Socket (Sold Separately)Front-connecting SocketP2CF-11Eleven, M3.5 × 7.5sems screws3Terminal Layout/Internal Connections(Top View)4.57.88 7 6 5Mounting Holes4Two, 4.5 dia mounting holes35.470 max.Two,4.5-dia.holes49310 11 1 240±0.2Note: Can also be mounted to a DIN track.50 max.31.2 max.Note: A model with finger protection (P2CF-11-E) is also available.Back-connecting SocketP3GA-1127 dia.473Terminal Layout/Internal Connections(Bottom View)5 6 7 844525.6392 1 11 10454.5 16.3 6.268.7Note: 1.

Using any other sockets will adversely affect accuracy. Use only the specified sockets.2. A Protective Cover for finger protection (Y92A-48G) is also available.Digital Temperature ControllersE5CN/E5CN-U13Operation■ Outline of Operation ProceduresThe following diagram illustrates the entire setting level. A password is required to enter the advance function setting level and the calibration level.Some parameters may not be displayed depending on the protection settings and operation conditions.The control operation will stop when switching from operation level to initial setting level.]Power ONStarting in manual modeStarting in automatic modePress the LevelKey for at least 1 s.Operation LevelCPress theLevel Keyless than 1 s.a-mPress the Level Keyfor at least 1 s;display will flash.Press the Level Key(Seefor at least 3 s whilenote 3.) a-m is displayed.ManualModeManualControl LevelPress theLevel Key forat least 1 s.Press theLevel + Mode Keys;display will flash.Adjustment LevelC(Seenote 1.)Press theLevel + ModeKeys.Press the Level Key for at least 1 s2510025100for at least 1 s;display will flash.Press the Level +Mode Keys for at least3 s.

(See note 4.)Press the Level Key forat least 3 s.Control stops .CommunicationsSetting LevelInitial Setting LevelCProtect LevelPress the Level Keyfor less than 1 s.Press the LevelKey for at least 1 s.Input password.Set value −169Advanced FunctionSetting LevelControl in progressInput password.Set value 1201Calibration LevelNote: 1.2.3.4.(Seenote 2.)Control stoppedNot displayed for some modelsLevel changeOperation level entered for software reset.You cannot move to other levels by operating the keys on the front panel from the calibration level. You must turn OFF the power supply.You can move only to the operation level by operating the keys on the front panel from the manual control level.The time taken to move to the protect level can be adjusted by changing the “Move to protect level time” setting.TroubleshootingIf an error occurs, an error message will be displayed on the No.

1 display. Use the error message to check the type of error and correct the erroraccordingly.No. 1 displayErrorCorrectionOutput status at errorControl outputs Alarm outputss.err (S. Err)Input error(See note 2.)Check for input wiring errors, broken wires, short-circuits, and input type error.OFFA/D convertererror(See note 2.)Check for an input error and then cycle the power supply. If the same error is stillOFFdisplayed, repairs will be necessary.If the Temperature Controller is normal after cycling the power supply, the error may havebeen caused by noise.

Check for noise being generated nearby.e111 (E111)Memory errorh.err (H. Err)Internal circuiterror(See note 2.)Cycle the power supply. If the same error is still displayed, repairs will be necessary.OFFIf the Temperature Controller is normal after cycling the power supply, the error may haveOFFbeen caused by noise. Check for noise being generated nearby.Handled asabnormally hightemperatureOFFOFFOFFNote: 1. If the input exceeds is within the controllable range but exceeds the display range (−1999 to 9999),will be displayed if the temperature is less than−1999 andwill be displayed if the temperature is more than 9999.

The control and alarm outputs will function normally during these displays. Referto the E5CN/E5CN-U Temperature Controller User's Manual (Cat. No. H129) for information on the controllable range.2. These errors are displayed only when the PV/SP is displayed. Errors are not displayed in other display modes.14Digital Temperature Controllers E5CN/E5CN-UDigital Temperature ControllersE5CN/E5CN-U15■ ParametersSome parameters are not displayed depending on themodel of the Controller and parameter settings.

For details,refer to the E5CN/E5CN-U Temperature Controller User'sManual (Cat. No. H129)Press the Level Key for at least 3 s.(Display flashes for at least 1 s.)Displays other than that for switchingbetween automatic and manualPower ONStarting in manual modeManual Control LevelC25 PID control onlyPress theLevel Keyfor atleast 1 s.PV/MVStarting in automaticmodePress the Level Key less than 1 s.Adjustment LevelOperation Levell.adjaAdjustment leveldisplayd Derivative time40offaac-sc Cooling coefficientct1 Heater current value 10.0 monitor1.00aCaaCahb1 Heater burnout 10.0 detection50.0wt-b Wait band0.0aasp-1 SP 10CSP used by multi-SPasp-2 SP 2sprt SP ramp set valuer-sc-o MV monitor (cooling)0.0aRun/stoprunaPress the Level + ModeKeys for at least 3 s.Display flashes.The time taken to move to the protect level canbe adjusted by changing the "Move to protectlevel time" setting.CommunicationsSetting LevelDisplayed only for models with communications.Changes are effective after cycling power or aftera software reset.aol-l MV lower limit0-5.0ashiftins Temperature input1-point shifta0.0insh Upper-limittemperature input0.02-point shiftainsl Lower-limit0.0 temperature inputpmoVSet either of these parameters.Move to protect levelDisplayed only when a password0 is set.