П-П_Реле (1031884), страница 2
Текст из файла (страница 2)
For details, refer to Load Current vs. Ambient Temperature inEngineering Data.Solid State Contactors (Three-phase)G3PBJ-49■ CharacteristicsModels with Built-in Heat SinksItemG3PB215B3N-VDG3PB215B2N-VDG3PB225B3N-VDG3PB225B2N-VDG3PB235B3N-VDG3PB235B2N-VDOperate time1/2 of load power source cycle + 1 ms max. (DC input)Release time1/2 of load power source cycle + 1 ms max. (DC input)Output ON voltage drop1.6 V (RMS) max.Leakage current(See note.)10 mA (at 200 VAC)Insulation resistance100 MΩ min. (at 500 VDC)Dielectric strength2,500 VAC, 50/60 Hz for 1 minVibration resistanceDestruction: 10 to 55 to 10 Hz, 0.175-mm single amplitude (Mounted to DIN track)Shock resistanceDestruction: 294 m/s2 (98 m/s2 with reverse mounting)Ambient temperatureOperating: –30°C to 80°C (with no icing or condensation)Storage: –30°C to 100°C (with no icing or condensation)Ambient humidityOperating: 45% to 85%WeightApprox.
1.25 kgCertified standardsUL508, CSA22.2 No. 14, EN60947-4-3 (IEC947-4-3); Certified by VDE(From April 2001)EMCEmissionImmunityESDImmunityElectromagneticImmunityEFTImmunitySurge transientImmunityRF disturbanceImmunityDipsApprox. 1.45 kgNote: The leakage current of phase S will be approximatelyJ-50Approx. 1.65 kgEN55011 Group 1 Class BIEC947-4-3, EN61000-4-24 kV contact discharge8 kV air dischargeIEC947-4-3, EN61000-4-310 V/m (80 MHz to 1 GHz)IEC947-4-3, EN61000-4-42 kV AC power-signal lineIEC947-4-3, EN61000-4-5Normal mode ±1 kV, Common mode ±2 kVIEC947-4-3, EN61000-4-610 V (0.15 to 80 MHz)IEC947-4-3, EN61000-4-113 times larger if the 2-element model is applied.Solid State Contactors (Three-phase) G3PBG3PB245B3N-VDApprox.
2.0 kgG3PB245B2N-VDItemG3PB515B3N-VDG3PB515B2N-VDG3PB525B3N-VDG3PB525B2N-VDG3PB535B3N-VDG3PB535B2N-VDOperate time1/2 of load power source cycle + 1 ms max. (DC input)Release time1/2 of load power source cycle + 1 ms max. (DC input)Output ON voltage drop1.8 V (RMS) max.Leakage current(See note.)20 mA (at 480 VAC)Insulation resistance100 MΩ min.
(at 500 VDC)Dielectric strength2,500 VAC, 50/60 Hz for 1 minVibration resistanceDestruction: 10 to 55 to 10 Hz, 0.175-mm single amplitude (Mounted to DIN track)Shock resistanceDestruction: 294 m/s2 (98 m/s2 with reverse mounting)Ambient temperatureOperating: –30°C to 80°C (with no icing or condensation)Storage:–30°C to 100°C (with no icing or condensation)Ambient humidityOperating: 45% to 85%WeightApprox.
1.25 kgCertified standardsUL508, CSA22.2 No. 14, EN60947-4-3 (IEC947-4-3); Certified by VDE(From April 2001)EMCEmissionImmunityESDImmunityElectromagneticImmunityEFTImmunitySurge transientImmunityRF disturbanceImmunityDipsApprox. 1.45 kgG3PB545B2N-VDApprox. 2.0 kgEN55011 Group 1 Class BIEC947-4-3, EN61000-4-24 kV contact discharge8 kV air dischargeIEC947-4-3, EN61000-4-310 V/m (80 MHz to 1 GHz)IEC947-4-3, EN61000-4-42 kV AC power-signal lineIEC947-4-3, EN61000-4-5Normal mode ±1 kV, Common mode ±2 kVIEC947-4-3, EN61000-4-610 V (0.15 to 80 MHz)IEC947-4-3, EN61000-4-113 times larger if the 2-element model is applied.SSRNote: The leakage current of phase S will be approximatelyApprox. 1.65 kgG3PB545B3N-VDSolid State Contactors (Three-phase)G3PBJ-51Engineering DataLoad Current vs. Ambient TemperatureModels with Built-in Heat SinksG3PB-225B-3N-VDG3PB-225B-2N-VDG3PB-525B-3N-VDG3PB-525B-2N-VDG3PB-235B-3N-VDG3PB-235B-2N-VDG3PB-535B-3N-VDG3PB-535B-2N-VDLoad current (A)Load current (A)G3PB-215B-3N-VDG3PB-215B-2N-VDG3PB-515B-3N-VDG3PB-515B-2N-VDG3PB-225B-3N-VDG3PB-225B-2N-VDG3PB-525B-3N-VDG3PB-525B-2N-VDG3PB-245B-3N-VDG3PB-245B-2N-VDG3PB-545B-3N-VDG3PB-545B-2N-VDG3PB-245B-3N-VDG3PB-245B-2N-VDG3PB-545B-3N-VDG3PB-545B-2N-VDG3PB-235B-3N-VDG3PB-235B-2N-VDG3PB-535B-3N-VDG3PB-535B-2N-VDG3PB-215B-3N-VDG3PB-215B-2N-VDG3PB-515B-3N-VDG3PB-515B-2N-VDAmbient temperature (°C)Ambient temperature (°C)Input impedance (kΩ )Input current (mA)Input Voltage vs.
Input Current and Input Voltage vs. Input ImpedanceInput currentInput impedanceInput voltage (V)One Cycle Surge Current: Non-repetitiveNote: Keep the inrush current to half the rated value if it occurs repetitively.G3PB-225B-3N-VD G3PB-225B-2N-VDG3PB-515B-3N-VD G3PB-515B-2N-VDG3PB-525B-3N-VD G3PB-525B-2N-VDEnergized time (ms)J-52G3PB-235B-3N-VDG3PB-235B-2N-VDG3PB-535B-3N-VDG3PB-535B-2N-VDG3PB-245B-3N-VDG3PB-245B-2N-VDG3PB-545B-3N-VDG3PB-545B-2N-VDInrush currentInrush currentInrush currentG3PB-215B-3N-VDG3PB-215B-2N-VDEnergized time (ms)Solid State Contactors (Three-phase) G3PBEnergized time (ms)DimensionsNote: All units are in millimeters unless otherwise indicated.G3PB-215B-3N-VD G3PB-515B-3N-VDG3PB-215B-2N-VD G3PB-515B-2N-VDG3PB-225B-2N-VD G3PB-525B-2N-VDWithout Terminal CoverWith Terminal CoverTwo, 4.6-dia. mounting holesFour, 8 dia.Two, M3.580.5max.100 max.Two, R2.3mountingholesSix, M4Terminal Arrangement/Internal Connections80 max.G3PB-@@@B-3N-VDInput circuitMounting Hole Dimensions30.5 max.120 max.G3PB-@@@B-2N-VDSSRInput circuitFour, 4.5-dia.
or M4Solid State Contactors (Three-phase)G3PBJ-53G3PB-225B-3N-VDG3PB-235B-2N-VDG3PB-525B-3N-VDG3PB-535B-2N-VDWithout Terminal CoverWith Terminal CoverTwo, 4.6-dia. mounting holesFour, 8 dia.Two, M3.580.5max.120max.Two, R2.3mountingholesSix, M5 (35 A type)Six, M4 (25 A type)Terminal Arrangement/Internal Connections80 max.G3PB-@@@B-3N-VD30.5 max.120 max.Input circuitMounting Hole DimensionsG3PB-@@@B-2N-VDInput circuitFour, 4.5-dia.
or M4J-54Solid State Contactors (Three-phase) G3PBG3PB-235B-3N-VDG3PB-245B-2N-VDG3PB-535B-3N-VDG3PB-545B-2N-VDWithout Terminal CoverWith Terminal CoverTwo, 4.6-dia. mounting holesFour, 8 dia.Two, M3.580.5max.140max.Two, R2.3mountingholesSix, M5Terminal Arrangement/Internal Connections80 max.G3PB-@@@B-3N-VDInput circuitMounting Hole Dimensions30.5 max.G3PB-@@@B-2N-VD120 max.SSRInput circuitFour, 4.5-dia.
or M4Solid State Contactors (Three-phase)G3PBJ-55G3PB-245B-3N-VDG3PB-545B-3N-VDWithout Terminal CoverWith Terminal CoverTwo, 4.6-dia. mounting holesFour, 8 dia.Two, M3.580.5max.140max.Two, R2.3mountingholesSix, M580 max.110 max.Terminal Arrangement/Internal ConnectionsG3PB-@@@B-3N-VDMounting Hole DimensionsInput circuit30.5 max.120 max.Four, 4.5-dia.or M4J-56Solid State Contactors (Three-phase) G3PBSafety PrecautionsSince the Relay is heavy, firmly mount the DIN track and fix bothends with End Plates for DIN-track-mounting models.Applicable DIN TracksThe G3PB can be mounted to TH35-15Fe (IEC60715) DIN tracks.The manufacturers and models of DIN tracks to which mounting ispossible are shown in the following table.ManufacturerThickness1.5 mm2.3 mmSchneiderAM1-DE200---WAGO210-114, 210-197210-118PHOENIXNS35/15NS35/15-2.3150.5mmCountermeasure 175mm max.Duct orairflowobstruction150.5mmSSRVerticaldirection(A height of nomore than halfthe SSR'sheight isrecommended)SSRIf the ducts cannot beshortened, place the SSRon a metal base so that itis not surrounded by theducts.Use short ducts.VentilationDirect MountingBe aware of air flowDuct orair flowobstructionVentilationoutletSSRSSRSSRWhen mounting directly onto a panel, mount securely under thefollowing conditions.Screw diameter: M4Tightening torque: 0.98 to 1.47 N·mAir inletMounted StateHorizontal MountingVertical directionVertical MountingAirflowSSRDuct orairflowobstructionDo not surround the SSRwith ducts, otherwise theheat radiation of the SSRwill be adversely affected.Countermeasure 2Mounting surfaceMounting MethodDuct HeightMounting surfacePlease observe the following precautions to prevent failure tooperate, malfunction, or undesirable effect on product performance.Relationship between SSRs and DuctsMounting surface■ Precautions for Correct UseIf the air inlet or air outlet has a filter, clean the filter regularly toprevent it from clogging and ensure an efficient flow of air.Do not locate any objects around the air inlet or air outlet, otherwisethe objects may obstruct the proper ventilation of the control panel.A heat exchanger, if used, should be located in front of the SSR Unitsto ensure the efficiency of the heat exchanger.Please reduce the ambient temperature of SSRs.PanelNote: Mount the G3PB sothat the markingscan be read.Note: When the G3PB ismounted horizontally,use at 50% of the ratedload current.Close MountingThe rated load current of an SSR is measured at an ambienttemperature of 25 or 40 °C.An SSR uses a semiconductor in the output element.
This causesthe temperature inside the control panel to increase due to heatingresulting from the passage of electrical current through the load. Torestrict heating, attach a fan to the ventilation outlet or air inlet of thecontrol panel to ventilate the panel. This will reduce the ambienttemperature of the SSRs and thus increase reliability. (Generally,each 10 °C reduction in temperature will double the expected life.)Three-element DevicesSSR Mounting PitchLoad current (A)15 ARequired number of fans 0.70per SSRPanel Mounting25 A1.0635 A1.6345 A2.09Duct or airflow obstructionTwo-element Devices80 mm min.SSRBetween ductor airflowobstructionand SSRMounting directionVertical direction80 mm min.80 mm min.Space betweenSSRs10mm min.Close mountingLoad current (A)15 ARequired number of fans 0.47per SSR25 A0.7835 A1.0945 A1.40Example: For 10 SSRs with load currents of 11 A (3-elementdevices,1.63 x 10 = 16.3Thus, 17 fans would be required.Size of fans: 92 mm2, Air volume: 0.7 m3/min,Ambient temperature of control panel: 30 °CIf there are other instruments that generate heat in the controlpanel other than SSRs, additional ventilation will be required.Solid State Contactors (Three-phase)G3PBJ-57SSRPanelWiringTightening TorqueWhen using crimp terminals, refer to the terminal clearances shownbelow.Refer to the following and be sure to tighten each screw of the Unit tothe specified torque in order to prevent the Unit from malfunctioning.Output TerminalsInput TerminalsItemScrew terminaldiameterTightening torqueInput terminalM3.50.59 to 1.18 N·mOutput terminalM40.98 to 1.47 N·mM51.47 to 2.45 N·mM4 (15 A, 25 A)M5 (35 A, 45 A)• Make sure that all lead wires are thick enough for the current.• Output terminals T1, T2, and T3 are charged regardless of whetherthe Unit is a 2- or 3-element model that is turned on or off.
Do nottouch these terminals, otherwise an electric shock may bereceived.To isolate the Unit from the power supply, install an appropriatecircuit breaker between the power supply and Unit.Be sure to turn off the power supply before wiring the Unit.• Terminal L2 and terminal T2 of the 2-element model are internallyshort-circuited to each other.
Therefore, connect terminal L2 to theground terminal side of the power supply. If terminal L2 isconnected to a terminal other than the ground terminal, cover allthe charged terminals, such as heater terminals, for the preventionof electric shock accidents and ground faults.ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.To convert millimeters into inches, multiply by 0.03937.
To convert grams into ounces, multiply by 0.03527.Cat. No. J135-E1-03J-58In the interest of product improvement, specifications are subject to change without notice.Solid State Contactors (Three-phase) G3PB.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
