62146 (Bipolar transistors)

6. Bipolar transistors

6.1. Device, constructive – technological features, circuit of insert

The bipolar transistor terms a three-electrode semiconductor device with two or more interacting electron-hole junction. In the transistor alternate as an electrical conductivity three regions of a semi-conductor, for what in a homogeneous semi-insulating substrate of silicon Si-i the methods of epiplanar technique shape regions of a collector, basis and emitter, (fig. 6.1). For it in a plate Si-n, employee by a collector, the method of a local diffusion (introduction of atoms of doping substance in a chip of a semi-conductor through some part of its surface) forms base region (Si-p). In this region also method of a local diffusion forms emitter region (Si-n) with high density of a donor dopant. On boundary region of emitter with base, and also on boundary of base region with collector are formed two electron-hole (p-n) junctions - emitter and collector (on a title of extreme regions of transistor structure).

Fig. 6.1. Planar n-p-n structure of the bipolar transistor

The junctions appear interacting, if distance between them, called in breadth of basis , is smaller diffusion lengths of mobile carriers of a charge. The diffusion length is a distance, which transits an electron and vacant electron site from a moment of occurrence in a semi-conductor up to a moment of a recombination .

The area of collector junction always is more than the area of emitter junction. The region of the emitter should have higher electrical conductivity, than basis and collector. An impurity concentration in the region of the transistor owe corresponds as:

. (6.1)

Depending on the order of alternation of regions as an electrical conductivity distinguish structures p-n-p and n-p-n of types.

In a fig. 6.2 the structures p-n-p and n-p-n and their legend on circuitries are shown.

Fig. 6.2. Flat one-dimensional model BT and legends

Fig. 6.3. The circuits of insert of bipolar transistors

As a device of an electric circuit, transistor use by such fashion, that one of its electrodes is entering, and another-output. The third electrode is common concerning an input and exit. Depending on what electrode is common, distinguish three circuits of insert of the transistor: common-base (CB), common emitter (CE) and common collector (CC) (fig. 6.3).

6.2. Conditions of insert of the transistor. Static parameters.

Physical processes

By operation of the transistor the voltages from exterior power supplys are affixed to its electrodes. Depending on polarity voltages affixed to electrodes, each of p-n-junctions the transistor can be switched on in direct or in the opposite direction. Four conditions of insert of the transistor are possible.

The table 6.1

1. Condition a splitting contact. In a condition a splitting contact both p-n- junction are backswitched on (high-ohmic state of a section E-C). In electrodes of the transistor the thermal currents backswitched of junctions flow past which are static parameters of a condition the splitting contact. In each of three circuits of insert of the transistor these parameters have particular magnitudes. Their labels look like

for the circuit with CB - ;

for the circuit with CE - ;

for the circuit with CC - ,

where the first index means an electrode, in which the current flows past;

the second index – circuit of insert;

the third index - requirement in the rest of the circuit:

о - absence of a current in the other electrode - no-load operation,

s - short-circuit in the rest of the circuit.

2. Condition of saturation. In a condition of saturation both p-n-junctions are directly switched on, the junctions saturated with mobile carriers of a charge, their resistances are small. The section E-C has high conductance and it is possible to consider it short-circuited.

Static parameters are the saturation currents in electrodes the transistor and residual voltages . A voltage ratio and currents relevant electrodes give magnitudes of resistances of saturation:

; .

3. Fissile condition. In a fig. 6.4 the flat one-dimensional model of the transistor is shown, which emitter junction is switched on in a forward direction, and collector junction - in backward. Such insert corresponds to a fissile condition, and the transistor has intensifying properties. The principle of operation of the transistor in a fissile condition grounded on use of the following phenomena:

- injection of majority carriers through emitter junction;

- transport of injected carriers through basis owing to diffusions and drift;

- recombination of nonequilibrium carriers in basis;

- extractions of carriers from basis in a collector by a region of collector junction.

The injection of carriers stipulates transiting through emitter p-n-junction of diffusive currents: hole and electronic .

In an external circuit of emitter the current of injection flows past

, (6.2)

where - hole current of injection of the emitter;

- electronic current of injection of the emitter.

For transistor structure p-n-p of a type the relation between admixtures in the emitter and basis is defined, as: . Therefore .

The relation between component of an emitter current is evaluated coefficient of injection

(6.3)

The injection of carriers from the emitter in basis rises density

minority carriers in basis. Their density on boundary of emitter junction for p-n-p of structure is defined by a relation

(6.4)

Appeared near to emitter junction in basis a charge of vacant electron sites almost instantaneous, during a dielectric relaxation seconds, is cancelled by a charge of electrons affluent in basis from a radiant . Circuit of a current the emitter - basis appears made and ensures course of an emitter current. Magnification near to emitter junction the electron concentrations and vacant electron sites are established by a lapse rate of densities nonequilibrium carriers in basis and . Under an operation of lapse rates densities there is a diffusive driving of nonequilibrium vacant electron sites and electrons through basis from the emitter to a collector.

Diffusion of vacant electron sites in basis is attended their recombination with by electrons. On place of recombined electrons in basis from the external circuits of a radiant act other electrons, establishing together with electrons leaving basis in the emitter, base current recombinations . As breadth of basis is much less diffusion lengths of carriers , a loss of carriers in basis at the expense of recombination is inappreciable, and current of a recombination on one, two order are less than a current .

The vacant electron sites injected by the emitter in basis and which have reached collector backswitched junction, get in its accelerating region and are thrown in region of a collector. The collector current is established: .

Process of transport of minority nonequilibrium carriers through basis is evaluated by a transport coefficient . Coefficient of transport depends from breadth of basis and diffusion length of vacant electron sites :

(6.5)

Than more vacant electron sites is injected by the emitter in basis, than more them extract a collector, augmenting a collector current. Therefore current is proportional to an emitter current and is termed current controlled of a collector, which in view of relations (6.3) and (6.5) is defined by a relation (6.6) also records as follows:

(6.6)

- is termed as an integrated (static) transmission factor current of emitter in a collector circuit and in view of relations (6.3), (6,5) is defined by the following formula:

. (6.7)

Opportunity of control of an output current of the transistor by change entering current is the important property of the bipolar transistor, allowing to use it as a fissile device of electronic circuits.