CCNA_2_UPD (1130967), страница 3
Текст из файла (страница 3)
Which packet destination addresswill R2 forward to R1?192.168.135.1192.168.142.1192.168.144.1192.168.128.145. Refer to the exhibit. R1 is running RIP with default parameters. R1 haslearned four different paths with the same metrics to network 192.168.6.0.Which path or paths will R1 use to forward a packet that is destined to192.168.6.10?the first path that the router learned.only the first two of the four paths that the router learned.the last path that the router learned.all four paths.46. What are two functions of a router? (Choose two.)It connects multiple IP networks.It controls the flow of data via the use of Layer 2 addresses.It determines the best path to send packets.It manages the VLAN database.It increases the size of the broadcast domain.47.
Refer to the exhibit. Which statement is true about the routing processfor this network?Стр. 5 из 2701.04.2009 0:45CISCO CCNA Certifications: CCNA 2 UPDATEDfile:///D:/botalka/%D1%81%D0%B8%D1%81%D1%8C%D0%BA...A packet leaves interface Fa0/0 of R1 with the source MAC address as000C.3010.9260.The packet leaves interface Fa0/0 of R1 with the source MAC address as000C.3010.9260.The no shutdown command needs to run on the Fa0/0 interface of R1.The Fa0/0 interface of R2 could be configured with the IP address 172.16.4.1/24.48.
Refer to the exhibit. A network administrator has run the show interfacecommand. The output of this command is displayed. What is the first stepthat is required to make this interface operational?Switch the cable with a known working cable.Issue the no shutdown command on the interface.Configure the interface as a loopback interface.Set the encapsulation for the interface.49. Refer to the exhibit. R1 is configured properly for a single area OSPF,and R2 has been recently installed in the network.
Which set of commandsis required to configure a single area OSPF for the networks that areconnected to R2?R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 150. Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 isrun on router R2.
What are the two results of this command? (Choose two.)A static route will be updated in the routing table.The traffic from the Internet will be directed to R2.The traffic from the source network 172.16.0.0/22 will be blocked.The route will be specified as the default route for all networks not defined in therouting table.All the broadcasts will be forwarded via the S0/0/0 interface of R2.51. Which three statements are true regarding the encapsulation andde-encapsulation of packets when traveling through a router? (Choosethree.)The router modifies the TTL field, decrementing it by one.The router changes the source IP to the IP of the exit interface.The router maintains the same source and destination IP.The router changes the source physical address to the physical address of the exitinterface.The router changes the destination IP to the IP of the exit interface.The router sends the packet out all other interfaces, besides the one it entered therouter on.52.
What are two tasks that must be completed before two routers can useOSPF to form a neighbor adjacency? (Choose two.)The routers must elect a designated router.The routers must agree on the network type.The routers must use the same dead interval.The routers must exchange link state requests.The routers must exchange database description packets.53. Refer to the exhibit. Although both the routers can ping the serialinterface of their neighbors, they are unable to ping the Ethernet interfacesof other routers. Which two statements are true for this network? (Choosetwo.)The administrative distance has been set to 50 on both routers.R2 is learning about network 192.168.1.0.R1 is learning about network 192.168.2.0.The network 10.1.1.0 command has not been run on both routers.Autosummarization is enabled on both routers.54. Which two situations require the use of a link-state protocol? (Choosetwo.)Fast convergence of the network is critical.The network is very large.The network administrator has limited knowledge to configure and troubleshootrouting protocols.The network is a flat network.The capacity of the router is low.55.
Refer to the exhibit. What information can be determined from thedisplayed output?EIGRP packets are waiting to be sent to the neighbors.The adjacencies between the routers are yet to be established.The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2.Router R2 is receiving hello packets from a neighbor with the IP address192.168.10.10 via the R2 S0/0/1 interface.56. Refer to the exhibit.
PC1 is unable to access the Internet. What is thecause of the problem?An incorrect IP address is configured between the two routers.No static route is configured on Router2.Стр. 6 из 2701.04.2009 0:45CISCO CCNA Certifications: CCNA 2 UPDATEDfile:///D:/botalka/%D1%81%D0%B8%D1%81%D1%8C%D0%BA...A routing loop has occurred.No routing protocol is configured on either of the two routers.57. Refer to the exhibit. What summarization should R2 use to advertise itsLAN networks to R1?172.16.0.0/24172.16.4.0/22172.16.4.0/23172.16.4.0/24comments (1)TOP05:22CCNA 2:Final Set 2POSTED BY ADMINOptions With Highlight Colours are Correct Answer1.
Refer to the exhibit. A new PC was deployed in the Sales network. It wasgiven the host address of 192.168.10.31 with a default gateway of192.168.10.17. The PC is not communicating with the network properly.What is the cause?The address is in the wrong subnet.192.168.10.31 is the broadcast address for this subnet.The default gateway is incorrect.The host address and default gateway are swapped.2.
Refer to the routing table shown in the exhibit. What is the meaning ofthe highlighted value 192?It is the value assigned by the Dijkstra algorithm that designates the number of hopsin the network.It is the value used by the DUAL algorithm to determine the bandwidth for the link.It is the metric, which is cost.It is the administrative distance.3. Refer to exhibit.
Given the topology shown in the exhibit, what threecommands are needed to configure EIGRP on the Paris router? (Choosethree.)Paris(config)# router eigrp 100Paris(config)# router eigrpParis(config-router)# network 192.168.6.0Paris(config-router)# network 192.168.7.0Paris(config-router)# network 192.168.8.0Paris(config-router)# network 192.168.9.04. What are three features of CDP? (Choose three.)tests Layer 2 connectivityprovides a layer of securityoperates a OSI layers 2 and 3enabled by default on each interfaceused for debugging Layer 4 connectivity issuesprovides information on directly connected devices that have CDP enabled5.
Refer to the exhibit. What two statements are true based on the outputshown? (Choose two.)the reported distance to network 172.16.1.0 is 2172416192.168.10.5 and 192.168.10.9 are feasible successorsneighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled.router 3 is load balancing traffic to the 172.16.3.0 network across its serialinterfaces.all interfaces shown on Router3 are in the passive state and will not send EIGRPadvertisements6. Which of the following should be considered when troubleshooting aproblem with the establishment of neighbor relationships between OSPFrouters? (Choose three.)OSPF interval timers mismatchgateway of last resort not redistributedinterface network type mismatchno loopback interface configuredadministrative distance mismatchinconsistent authentication configuration7.
![](https://s.studizba.com/z.php?f=/templates/si/i/noavatar.png&w=100&h=100&t=1"){kind=avatar}
