Cordless Telephones (Несколько текстов для зачёта)

Cordless Telephones

Cordless telephones are one of those minor miracles of modern life - with a cordless phone, you can talk on the phone while moving freely about your house or in your yard. Long before cell phones became so cheap that anyone could afford one, cordless phones gave everyone the freedom to walk and talk within the privacy of their own homes. A cordless telephone is basically a combination telephone and radio transmitter/receiver. A cordless phone has two major parts: base and handset.

Base
The base unit of the cordless phone is plugged into the telephone jack on your wall. If you open up the base and expose the circuit board, you see several components that carry out the functions of the base:

• phone line interface - receives and sends telephone signals through the phone line

• radio

• amplifies signals to and from phone-line interface, user controls and speaker phone (if present)

• broadcasts and receives radio signals to and from the handset

• power - supplies low voltage power to the circuits and recharges the battery of the handset

Phone Line Interface
Phone line interface components do two things. First, they send the ringer signal to the bell (if it's on the base) or to the radio components for broadcast to the handset. This lets you know that you have an incoming call. Second, they receive and send small changes in the phone line's electrical current to and from the radio components of the base. When you talk, you cause small changes in the electrical current of the phone line, and these changes get sent to your caller. The same happens when the caller talks to you.

Radio Components
The radio components receive the electrical signals from the phone line interface and user controls (keypads, buttons). The radio components convert the signals to radio waves and broadcast them via the antenna. Radio components use quartz crystals to set the radio frequencies for sending and receiving. There are two quartz crystals, one for sending signals and one for receiving signals. Remember that the base and handset operate on a frequency pair that allows you to talk and listen at the same time (duplex). The radio components include an audio amplifier that increases the strength of the incoming electrical signals.

Power Components
A DC power cube transformer supplies the low voltage required by the electrical components on the circuit board. The power components on the circuit board work with the power cube to supply electrical current to re-charge the battery of the handset.

In addition to the above components, some bases also have audio amplifiers to drive speakers for speaker phone features, keypads for dialing, liquid crystal displays (LCDs) for caller ID, light-emitting diodes (LEDs) for power/charging indicators, and solid state memory for answering machine or call-back features.

Handset

You can carry the handset with you throughout the house or outside within the range of the base transmitter. The handset has all of the equipment of a standard telephone (speaker, microphone, dialing keypad), plus the equipment of an FM radio transmitter/receiver. When you open up the handset, you can see these components.

Speaker
The speaker receives the electrical signals from the audio amplifier in the radio components and converts them into sound. When you remove the cover from the speaker, you see a large round permanent magnet with a hole in the middle and a deep groove surrounding the hole. Within this deep groove is a coil of fine copper wire that is attached to a thin plastic membrane. The plastic membrane covers the magnet and coil.

Microphone
The microphone changes the sound waves from your voice into electrical signals that are sent to the audio amplifier of the radio components. A microphone is essentially a speaker that works in reverse. When sound waves from your voice move the membrane, they make tiny electric currents either by moving a coil of wire within a magnet or by compressing the membrane against carbon dust.

Keypad
The keypad allows you to dial a number. It transfers the pressure from your fingertip on the appropriate key into an electrical signal that it sends to the radio components. Below the rubber keypad is a circuit board with black conductive material under each button. The keypad works like a remote control. When you press a button, it makes a contact with the black material and changes its electrical conductance. The conductance sends an electrical signal to the radio components indicating that you have selected that number.

Buzzer or Ringer
When the radio components of the handset receive the ringer signal from the base, they send electrical signals to the buzzer. The buzzer changes those electrical signals into sound much like the speaker does. You hear the buzzer sound and know that someone is calling you. In some phones, the speaker is used to make the ringer sound and there is no need for a separate ringer.

Radio Components

The radio components of the handset are like those of the base - they convert electrical signals from the microphone into FM radio signals and broadcast them at the same frequency as the receiving crystal of the base unit. The radio components also receive radio signals at the same frequency as the broadcasting crystal from the base, convert them to electrical signals and send them to the speaker and/or buzzer (ringer).

Battery
The handset's battery supplies the power for all of the electrical components in the handset. All cordless phone handsets have a rechargeable battery (nickel-cadmium, nickel-metal hydride or lithium). When the battery runs low, an indicator light on the handset usually lights up or flashes. In some phones, a "beeping" sound may also indicate a low battery. You then recharge the battery on the base of the cordless phone.

The GE cordless phone that we dissected was from 1993. Modern cordless phones have the same functions and much of the same hardware. However, many of the electronic circuits that were once achieved with transistors, resistors and capacitors have been replaced with integrated circuits. This advancement allows the handset to be either smaller with the same functions or the same size with more functions.

In summary, a cordless phone is basically a combination of a telephone and an FM radio transmitter/receiver. Because it is a radio transmitter, it broadcasts signals over the open airways rather than specifically between the base and handset.