A little bit of physics (Несколько текстов для зачёта), страница 4

Blow molding is used to form bottles and other containers from soft, hollow thermoplastic tubes. First a mold is fitted around the outside of the softened thermoplastic tube, and then the tube is heated. Next, air is blown into the softened tube (similar to inflating a balloon), which forces the outside of the softened tube to conform to the inside walls of the mold. Once the plastic cools, the mold is opened and the newly molded container is removed. Blow molding is used to make many plastic containers, including soft-drink bottles, jars, detergent bottles, and storage drums.

Blow Film Extrusion

Blow film extrusion is the process used to make plastic garbage bags and continuous sheets. This process works by extruding a hollow, sealed-end thermoplastic tube through a die opening. As the flattened plastic tube emerges from the die opening, air is blown inside the hollow tube to stretch and thin the tube (like a balloon being inflated) to the desired size and wall thickness.

The plastic is then air-cooled and pulled away on take-up rollers to a heat-sealing operation. The heat-sealer cuts and seals one end of the thinned, flattened thermoplastic tube, creating various bag lengths for products such as plastic grocery and garbage bags. For sheeting (flat film), the thinned plastic tube is slit along one side and opened to form a continuous sheet.

Calendering

The calendering process forms continuous plastic sheets that are used to make flooring, wall siding, tape, and other products. These plastic sheets are made by forcing hot thermoplastic resin between heated rollers called calenders. A series of secondary calenders further thins the plastic sheets. Paper, cloth, and other plastics may be pressed between layers of calendered plastic to make items such as credit cards, playing cards, and wallpaper.

Thermoforming

Thermoforming is a term used to describe several techniques for making products from plastic sheets. Products made from thermoformed sheets include trays, signs, briefcase shells, refrigerator door liners, and packages. In a vacuum-forming process, hot thermoplastic sheets are draped over a mold. Air is removed from between the mold and the hot plastic, which creates a vacuum that draws the plastic into the cavities of the mold. When the plastic cools, the molded product is removed. In the pressure-forming process, compressed air is used to drive a hot plastic sheet into the cavities and depressions of a concave, or female, mold. Vent holes in the bottom of the mold allow trapped air to escape.

Forming Thermosetting Plastics

Thermosetting plastics are manufactured by several methods that use heat or pressure to induce polymer molecules to bond, or cross-link, into typically hard and durable products.

Compression Molding

Compression molding forms plastics through a technique that is similar to the way a waffle iron forms waffles from batter. First, thermosetting resin is placed into a steel mold. The application of heat and pressure, which accelerate cross-linking of the resin, softens the material and squeezes it into all parts of the mold to form the desired shape. Once the material has cooled and hardened, the newly formed object is removed from the mold. This process creates hard, heat-resistant plastic products, including dinnerware, telephones, television set frames, and electrical parts.

Laminating

The laminating process binds layers of materials, such as textiles and paper, together in a plastic matrix. This process is similar to the process of joining sheets of wood to make plywood. Resin-impregnated layers of textiles or paper are stacked on hot plates, then squeezed and fused together by heat and pressure, which causes the polymer molecules to cross-link. The best-known laminate trade name is Formica, which is a product consisting of resin-impregnated layers of paper with decorative patterns such as wood grain, marble, and colored designs. Formica is often used as a surface finish for furniture, and kitchen and bathroom countertops. Thermosetting resins known as melamine and phenolic resins form the plastic matrix for Formica and other laminates. Electric circuit boards are also laminated from resin-impregnated paper, fabric, and glass fibers.

Reaction Injection Molding (RIM)

Strong, sizable, and durable plastic products such as automobile body panels, skis, and business machine housings are formed by reaction injection molding. In this process, liquid thermosetting resin is combined with a curing agent (a chemical that causes the polymer molecules to cross-link) and injected into a mold. Most products made by reaction injection molding are made from polyurethane.

Forming Both Types of Plastics

Certain plastic fabrication processes can be used to form either thermoplastics or thermosetting plastics.

Casting

The casting process is similar to that of molding plaster or cement. Fluid thermosetting or thermoplastic resin is poured into a mold, and additives cause the resin to solidify. Photographic film is made by pouring a fluid solution of resin onto a highly polished metal belt. A thin plastic film remains as the solution evaporates. The casting process is also used to make furniture parts, tabletops, sinks, and acrylic window sheets.

Expansion Processes

Thermosetting and thermoplastic resins can be expanded by injecting gases (often nitrogen or methyl chloride) into the plastic melt. As the resin cools, tiny bubbles of gas are trapped inside, forming a cellular plastic structure. This process is used to make foam products such as cushions, pillows, sponges, egg cartons, and polystyrene cups.

Foam plastics can be classified according to their bubble, or cell, structure. Sponges and carpet pads are examples of open-celled foam plastics, in which the bubbles are interconnected. Flotation devices are examples of closed-celled foam plastics, in which the bubbles are sealed like tiny balloons. Foam plastics can also be classified by density (ratio of plastic to cells), by the type of plastic resin used, and by flexibility (rigid or flexible foam). For example, rigid, closed-celled polyurethane plastics make excellent insulation for refrigerators and freezers.

IMPORTANT TYPES OF PLASTICS

A wide variety of both thermoplastics and thermosetting plastics are manufactured. These plastics have a spectrum of properties that are derived from their chemical compositions. As a result, manufactured plastics can be used in applications ranging from contact lenses to jet body components.

Thermoplastics

Thermoplastic materials are in high demand because they can be repeatedly softened and remolded. The most commonly manufactured thermoplastics are presented in this section in order of decreasing volume of production.

Polyethylene

Polyethylene (PE) resins are milky white, translucent substances derived from ethylene (CH₂CH₂). Polyethylene, with the chemical formula [CH₂CH₂]_n (where n denotes that the chemical formula inside the brackets repeats itself to form the plastic molecule) is made in low- and high-density forms. Low-density polyethylene (LDPE) has a density ranging from 0.91 to 0.93 g/cm3 (0.60 to 0.61 oz/cu in). The molecules of LDPE have a carbon backbone with side groups of four to six carbon atoms attached randomly along the main backbone. LDPE is the most widely used of all plastics, because it is inexpensive, flexible, extremely tough, and chemical-resistant. LDPE is molded into bottles, garment bags, frozen food packages, and plastic toys.

High-density polyethylene (HDPE) has a density that ranges from 0.94 to 0.97 g/cm3 (0.62 to 0.64 oz/cu in). Its molecules have an extremely long carbon backbone with no side groups. As a result, these molecules align into more compact arrangements, accounting for the higher density of HDPE. HDPE is stiffer, stronger, and less translucent than low-density polyethylene. HDPE is formed into grocery bags, car fuel tanks, packaging, and piping.

Polyvinyl Chloride

Polyvinyl chloride (PVC) is prepared from the organic compound vinyl chloride (CH₂CHCl). PVC is the most widely used of the amorphous plastics. PVC is lightweight, durable, and waterproof. Chlorine atoms bonded to the carbon backbone of its molecules give PVC its hard and flame-resistant properties.

In its rigid form, PVC is weather-resistant and is extruded into pipe, house siding, and gutters. Rigid PVC is also blow molded into clear bottles and is used to form other consumer products, including compact discs and computer casings.

PVC can be softened with certain chemicals. This softened form of PVC is used to make shrink-wrap, food packaging, rainwear, shoe soles, shampoo containers, floor tile, gloves, upholstery, and other products. Most softened PVC plastic products are manufactured by extrusion, injection molding, or casting.

Polypropylene

Polypropylene is polymerized from the organic compound propylene (CH₃CHCH₂) and has a methyl group (CH₃) branching off of every other carbon along the molecular backbone. Because the most common form of polypropylene has the methyl groups all on one side of the carbon backbone, polypropylene molecules tend to be highly aligned and compact, giving this thermoplastic the properties of durability and chemical resistance. Many polypropylene products, such as rope, fiber, luggage, carpet, and packaging film, are formed by injection molding.

Polystyrene

Polystyrene, produced from styrene (C₆H₅CHCH₂), has phenyl groups (six-member carbon ring) attached in random locations along the carbon backbone of the molecule. The random attachment of benzene prevents the molecules from becoming highly aligned. As a result, polystyrene is an amorphous, transparent, and somewhat brittle plastic. Polystyrene is widely used because of its rigidity and superior insulation properties. Polystyrene can undergo all thermoplastic processes to form products such as toys, utensils, display boxes, model aircraft kits, and ballpoint pen barrels. Polystyrene is also expanded into foam plastics such as packaging materials, egg cartons, flotation devices, and styrofoam.

Polyethylene Terephthalate

Polyethylene terephthalate (PET) is formed from the reaction of terephthalic acid (HOOCC₆H₄COOH) and ethylene glycol (HOCH₂CH₂OH), which produces the PET monomer [OOCC₆H₄COOCH₂CH₂]_n. PET molecules are highly aligned, creating a strong and abrasion-resistant material that is used to produce films and polyester fibers. PET is injection molded into windshield wiper arms, sunroof frames, gears, pulleys, and food trays. This plastic is used to make the trademarked textiles Dacron, Fibre V, Fortrel, and Kodel. Tough, transparent PET films (marketed under the brand name Mylar) are magnetically coated to make both audio and video recording tape.

Acrylonitrile Butadiene Styrene

Acrylonitrile butadiene styrene (ABS) is made by copolymerizing (combining two or more monomers) the monomers acrylonitrile (CH₂CHCN) and styrene (C₆H₅CHCH₂). Acrylonitrile and styrene are dissolved in polybutadiene rubber [CHCHCHCH] _n, which allows these monomers to form chains by attaching to the rubber molecules.

The advantage of ABS is that this material combines the strength and rigidity of the acrylonitrile and styrene polymers with the toughness of the polybutadiene rubber. Although the cost of producing ABS is roughly twice the cost of producing polystyrene, ABS is considered superior for its hardness, gloss, toughness, and electrical insulation properties. ABS plastic is injection molded to make telephones, helmets, washing machine agitators, and pipe joints. This plastic is thermoformed to make luggage, golf carts, toys, and car grills. ABS is also extruded to make piping, to which pipe joints are easily solvent-cemented.

Polymethyl Methacrylate

Polymethyl methacrylate (PMMA), more commonly known by the generic name acrylic, is polymerized from the hydrocarbon compound methyl methacrylate (C₄O₂H₈). PMMA is a hard material and is extremely clear because of the amorphous arrangement of its molecules. As a result, this thermoplastic is used to make optical lenses, watch crystals, aircraft windshields, skylights, and outdoor signs. These PMMA products are marketed under familiar trade names, including Plexiglas, Lucite, and Acrylite. Because PMMA can be cast to resemble marble, it is also used to make sinks, countertops, and other fixtures.

Polyamide

Polyamides (PA), known by the trade name Nylon, consist of highly ordered molecules, which give polyamides high tensile strength. Some polyamides are made by reacting dicarboxylic acid with diamines (carbon molecules with the ion –NH₂ on each end), as in nylon-6,6 and nylon-6,10. (The two numbers in each type of nylon represent the number of carbon atoms in the diamine and the dicarboxylic acid, respectively.) Other types of nylon are synthesized by the condensation of amino acids.

Polyamides have mechanical properties such as high abrasion resistance, low coefficients of friction (meaning they are slippery), and tensile strengths comparable to the softer of the aluminum alloys. Therefore, nylons are commonly used for mechanical applications, such as gears, bearings, and bushings. Nylons are also extruded into millions of tons of synthetic fibers every year. The most commonly used nylon fibers, nylon-6,6 and nylon-6 (single number because this nylon forms by the self-condensation of an amino acid) are made into textiles, ropes, fishing lines, brushes, and other items.